how to solve error of subscripted dimension mismatch?

1 次查看（过去 30 天）

显示更早的评论

Roshni Khetan 2017-10-2

0
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/359363-how-to-solve-error-of-subscripted-dimension-mismatch

关闭： MATLAB Answer Bot 2021-8-20

在 MATLAB Online 中打开

% the code works for one iteration and stops at column 27 for the second iteration
  T_air_DIC1 = [];
i =1;
T_air_DIC1(1) = 78; %input('input the lowest possible value of T_air_in_DIC1 in Celsius');
T_air_DIC1_max = 94; %input('input the maximum possible value of T_air_in_DIC1 in Celsius');
k = T_air_DIC1_max - T_air_DIC1(1);
no_data_pt = k+1;
c =2;
 max_temp = T_air_DIC1_max+1;
%%finding water flow rates for different inlet air temp.'s to DIC1 to obtain the required set point temperatures
while T_air_DIC1(i) < max_temp
    guess1 = 3.5; %input('a expected guess flow rate for water into IC1');
    guess2 = 1.5; %input('a expected guess flow rate for water into DIC1');
    x0 = [guess1,guess2];
    x = fsolve(@(x)LPCA1_ctrlscheme(x,T_air_DIC1(i),T_sp_AC,T_sp_DIC1,T_0,P_0,RH_0,P_out,Flow_required),x0);
    m_wat_DIC1(i) = x(2);
    m_wat_IC1(i) = x(1);
    m_wat_AC(i) = x(1) + x(2);
    [P,T,T_w_out,T_w_in,Q,RH] = LPCA1ctrlschemenew(x(1),x(2),T_air_DIC1,...
        T_sp_AC,T_sp_DIC1,T_0,P_0,RH_0,P_out,Flow_required);
    %    while c <no_data_pt+1
    DataSummary(c,1) = T_0;
    DataSummary(c,2) = P_0/1000;
    DataSummary(c,3) = RH_0;
    index = length(T);  % T is a vector in the compressor file which has all the temperature state points
    DataSummary(c,4:3+index) = T; % 3+index is the last column where Temp. state point value is stored,
    %it begins from 4 & cotinues till 11
    %DataSummary(c,4+index:3+index*2) = P; % from 12 to 19
    DataSummary(c,12:19) = P;
    %DataSummary(c,4+index*2:3+index*3) = RH; % from 20 to 27
    DataSummary(c,20:27) = RH; % from 20 to 27
    ind = length(T_w_out);
    % DataSummary(c,4+index*3:ind+3+index*3) = T_w_out; % temp. of water leaving the HEXs from 28 to 30
    DataSummary(c,28:30) = T_w_out;
    %DataSummary(c,1+ind+3+index*3:ind +ind+3+index*3) = T_w_in; % temp. of water entering the HEXs from 31 to 33
    DataSummary(c,31:33) = T_w_out;
    DataSummary(c,34:36) = Q/1000; % heat recovered across the compressor HEXs
    DataSummary(c,37) = m_wat_DIC1(i); % flow rate of water through DIC1 (kg/sec)
    DataSummary(c,38) = m_wat_IC1(i); % flow rate of water through IC1 (kg/sec)
    DataSummary(c,39) = m_wat_AC(i); % flow rate of water through AC(kg/sec)
    DataSummary(c,40) = T_air_DIC1(i); % temp. of air entering DIC1(C)
    i = i+1;
    c = c+1;
   T_air_DIC1(i) = T_air_DIC1(i-1) + 1;
   end

1 个评论
显示 -1更早的评论隐藏 -1更早的评论

OCDER 2017-10-2

在 MATLAB Online 中打开

Post the full error message, which should show the line number where the error occurred. That way, we don't have to figure out where in the code is causing an issue.

Also, use the {} Code button to make your code readable like this: