where can i see task overruns while running a simulink model on raspberry pi

Question

breezer 2017-11-10

0
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/366260-where-can-i-see-task-overruns-while-running-a-simulink-model-on-raspberry-pi

评论： Madhu Govindarajan 2018-2-8

Hello,

i use the hardware support to run simulink models on Raspberry pi. In the previously used Matlab R2015b i got an Command-line window which displayed me task overruns after the compilation process.

Now i will use Matlab R2017a and the problem is that this Command-line window does not appear after the compilation process.

The question is: how can i see task overruns or how can i activate this Command-line window?

Kind regards...

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

请先登录，再回答此问题。

Answer 1

Nick Choi 2017-11-13

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/366260-where-can-i-see-task-overruns-while-running-a-simulink-model-on-raspberry-pi#answer_290871

You can detect task overruns for a Simulink model running on a Raspberry Pi by enabling 'Enable overrun detection' in the model's configuration parameters as described in this documentation page:

https://www.mathworks.com/help/supportpkg/raspberrypi/ug/detect-and-fix-overruns-on-raspberry_pi-hardware.html

1 个评论
显示 -1更早的评论隐藏 -1更早的评论

Madhu Govindarajan 2017-11-13

If you follow these steps, when there is a task overrun the digital LED on the Pi blinks at a constant rate.

请先登录，再进行评论。

Answer 2

breezer 2017-11-15

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/366260-where-can-i-see-task-overruns-while-running-a-simulink-model-on-raspberry-pi#answer_291300

编辑：breezer 2017-11-15

Thank you for your reply,

yes you are right Madhu, the LED is flashing if an overrun occurs. In my opinion it is a step backwards to remove the CMD-Line messages, because a flashing LED can also be a memory write or something.

Nevertheless, is it possible to activate the old overrun message via CMD-Line window somehow?

2 个评论
显示无隐藏无

Madhu Govindarajan 2017-11-15

I personally have never experienced what you are referring to with R2015b (CMD-line message), so cannot comment much. But I feel like this might be related to the View Diagnostics stuff.

Have you checked the View Diagnostics pane for these types of warnings? https://www.mathworks.com/help/simulink/ug/diagnose-simulation-errors.html

breezer 2017-11-15

I have taken a screenshot of the CMD-Line window wich display some overruns... The Diagnostic-View shows no errors or warnings...

请先登录，再进行评论。

Answer 3

Ashley Warne 2018-2-7

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/366260-where-can-i-see-task-overruns-while-running-a-simulink-model-on-raspberry-pi#answer_303936

编辑：Ashley Warne 2018-2-7

A MODELNAME.log file is created in the same folder on the Rasp Pi as the model. Overruns are reported in this file. If you open up a remote command line session to the Rasp Pi as explained in the link below then you can run the command "cat MODELNAME.log" to print out this file to the screen and see if the model is over running. This works even while the model is running.

https://uk.mathworks.com/help/supportpkg/raspberrypi/ug/opening-a-serial-command-line-session-with-your-raspberry_pi-hardware.html

Make sure you enable overrun detection.

@Mathworks - The documentation mentions nothing about the LED and still refers to errors being thrown to the command line. The LED doesn't provide useful feedback anyway as it's always blinking for one reason or another. Perhaps you should mention that the .log file can be inspected to determine if the model is overrunning.

1 个评论
显示 -1更早的评论隐藏 -1更早的评论

Madhu Govindarajan 2018-2-8

That is definitely valuable feedback. I have passed on your feedback to MathWorks developer who works on this product for their consideration to update the documentation.

请先登录，再进行评论。