Whiteout regions on Contour Plot

Question

laoliu102 2017-12-14

1
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/373008-whiteout-regions-on-contour-plot

评论： Walter Roberson 2023-3-31

I don't want to display certain regions of the contour plot. How can I whiteout these regions on the contour plot? The interpolated data fills the entire space while the real data has blank regions that physically don't contain anything. These blank regions are the regions that I don't want to display on the contour plot. I have attached the two plots.

I have the scatter plot data as x,y,z arrays and the interpolated data for the contour plot as x,y,z matrices.

Any help/suggestion is welcomed and appreciated. Thank you.

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

请先登录，再回答此问题。

Answer 1

Walter Roberson 2017-12-14

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/373008-whiteout-regions-on-contour-plot#answer_296296

My recommendation would be to set the interpolated data to nan in those regions before doing the contour plot.

However, since you have scattered data, you have the challenge of determining which points are "near enough" to explicit scattered data that they should validly be interpolated, and which points are instead to be interpreted as being too far from the scattered data and so should be interpreted as being outside the map.

You could consider a pdist2() approach but it appears you have a fair bit of data, so that would not be computationally feasible. You might be able to take advantage of kd-tree approaches; https://www.mathworks.com/help/stats/classification-using-nearest-neighbors.html

6 个评论
显示 4更早的评论隐藏 4更早的评论

Walter Roberson 2017-12-14

在 MATLAB Online 中打开

Are you doing something similar to

 qxvec = linspace(min(x), max(x), 76);
 qyvec = linspace(min(y), max(y), 96);
 [qx, qy] = ndgrid(qxvec, qyvec);
 qz = griddedInterpolant(x, y, z, qx, qy);

In such a case then by default you would be using bilinear interpolation, so the value at each gridpoint qx(I,J), qy(I,J) would be determined by the four points in the x, y vectors nearest to the query points, and no other data points would be used.

Or are you doing something like a density plot, or something like a maximum intensity projection plot? Or something like creating a grid and determining where each point fits on it, and averaging all of the points in any one grid location?

If you did happen to be using an approach involving gridding the points and then considering the properties of the subset of points within each grid location, then that would make it relatively easy to determine which grid locations were empty and to assign nan to them. The trade off in such a case is that there could well be an adjacent point "just outside" the grid location whose influence would not be considered at all. But that might be acceptable for your purposes.

Walter Roberson 2017-12-14

在 MATLAB Online 中打开

cutoff_distance = 6.28;   %set as appropriate
[xi,yi] = meshgrid(300:20:2200, 300:20:1800);
zi = griddata(xn, yn, zn, xi, yi);
DT = delaunayTriangulation(xn, yn);
[vi, d] = nearestNeighbor(DT, xi(:), yi(:));
mask = d > cutoff_distance;
zi(mask) = nan;

laoliu102 2017-12-17

Thank you so much! It works now!

请先登录，再进行评论。

Answer 2

Muhammad Usman 2019-11-6

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/373008-whiteout-regions-on-contour-plot#answer_400178

I have got the same problem but mine was a little bit simple. I use the built-in MATLAB function "scatterInterpolant" to plot a contour. The plot is shown below.

It's s stress contour and the ellipse is an empty space and there are no nodes inside the ellipse. I want the ellipse to be whiteout. Somehow I managed to set the values inside the ellipse to be zero (because I can't delete them) and I got the following result

I want the ellipse to be whiteout. Any sort of help is highly appreciated. Thanks in advance.

P.S. I use the fill command to fill the ellipse with white color but that's not a proper way to do it.

8 个评论
显示 6更早的评论隐藏 6更早的评论

Jiandong 2023-3-31

在 MATLAB Online 中打开

Maybe you can use the inpolygon function

[in,on] = inpolygon(x_list,y_list,ellipse_x,ellipse_y);
    for i = 1:length(x_list)
        if(in(i))
            ellipse_x(i)=NaN;
            ellipse_y(i)=NaN;
        end
    end

Walter Roberson 2023-3-31

在 MATLAB Online 中打开

@Jiandong

That suggests to me that you could use the shorter

[in,on] = inpolygon(x_list,y_list,ellipse_x,ellipse_y);
ellipse_x(in) = NaN;
ellipse_y(in) = NaN;

请先登录，再进行评论。

Whiteout regions on Contour Plot

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

采纳的回答

6 个评论
显示 4更早的评论隐藏 4更早的评论

更多回答（1 个）

8 个评论
显示 6更早的评论隐藏 6更早的评论

另请参阅

类别

标签

Community Treasure Hunt

Whiteout regions on Contour Plot

0 个评论 显示 -2更早的评论隐藏 -2更早的评论

采纳的回答

6 个评论 显示 4更早的评论隐藏 4更早的评论

更多回答（1 个）

8 个评论 显示 6更早的评论隐藏 6更早的评论

另请参阅

类别

标签

Community Treasure Hunt

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

6 个评论
显示 4更早的评论隐藏 4更早的评论

8 个评论
显示 6更早的评论隐藏 6更早的评论