How to use Simulink.Bus.createMATLABStruct function with Simulink Data Dictionaries

Question

simon pierce 2018-6-11

1
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/405042-how-to-use-simulink-bus-creatematlabstruct-function-with-simulink-data-dictionaries

回答： Sebastian 2023-10-10

在 MATLAB Online 中打开

I have a Simulink Constant Block where the value is

Simulink.Bus.createMATLABStruct('myBus');

in order to create a Simple test-harness.

If the bus-object for 'myBus' is in the base-workspace then it works. However, if the bus-object is defined (solely) in a linked data-dictionary then it does not.

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

请先登录，再回答此问题。

Answer 1

Ivan 2019-1-23

3
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/405042-how-to-use-simulink-bus-creatematlabstruct-function-with-simulink-data-dictionaries#answer_357622

编辑：Ivan 2020-1-17

在 MATLAB Online 中打开

you can also try next code:

dd_name=get_param('Model Name','DataDictionary');
scope = Simulink.data.DataDictionary(dd_name);
pStruct=[];
dims=[1,1];
obj='BUS_NAME';
BUS_NAME_MATLABStruct = Simulink.Bus.createMATLABStruct(obj, pStruct, dims, scope);

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

Answer 2

simon pierce 2018-7-2

1
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/405042-how-to-use-simulink-bus-creatematlabstruct-function-with-simulink-data-dictionaries#answer_327143

在 MATLAB Online 中打开

I have created the following function as a stopgap.

function myStruct = CreateMatlabStructDD( busName , partialValues ) 
% this function relies on the bus-object being specified in the simulink
% data dictionary
% get this models data dictionary
dataDictionaryFile = get_param(gcs, 'DataDictionary');
% create a data dictionary object 
slddObject = Simulink.data.dictionary.open(dataDictionaryFile);
% get the design data section
section = getSection(slddObject, 'Design Data');
% get the buses
entries = find(section, '-value', '-class', 'Simulink.Bus');
% find the one we want 
myBus  = find(entries, 'Name', busName);
% turn in ot a cell array 
myBusCell = getValue(myBus);
% assign in to the base workspace, with the same name as in the
% data-dictionary
assignin('base', busName, myBusCell);
% create the structure with Mathworks createMATLABStruct function, which is
% possible now that it is in the base workspace
myStruct = Simulink.Bus.createMATLABStruct( busName, partialValues );
end

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

Answer 3

Robert Simpson 2018-6-11

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/405042-how-to-use-simulink-bus-creatematlabstruct-function-with-simulink-data-dictionaries#answer_324174

I also have this issue. Automatically created test harnesses try to set initial condition of ZOH blocks by running Simulink.Bus.createMATLABStruct('.....'); in the mask of the signal spec block. But this fails.

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

Answer 4

Sebastian 2023-10-10

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/405042-how-to-use-simulink-bus-creatematlabstruct-function-with-simulink-data-dictionaries#answer_1330089

If you have nested buses in your data dictionary it gets even more complicated, because you have to load all referenced buses to the base workspace as well.

Is there an easier way available in the latest releases?