how to make the plot change color atomatic ?
10 次查看(过去 30 天)
显示 更早的评论
for exmaple this is my code :
clc;clear all;close all;
f=[10 50 100];
T=1./f;
for i=1:length(T)
t(i,:)=linspace(0,2*T(i),10000);
subplot(3,1,i);
y(i,:)=sin(2*pi*t(i,:).*f(i));
plot(t(i,:),y(i,:),'--');
title(sprintf('y=sin(2*pi*t*%d)', f(i)));
hold on;
end
as you can see from the code the frequency changes automatically in the title ,is there a possible to change the color automatically too ? for example the first plot will be blue,the second green, and the third yellow ?
0 个评论
回答(1 个)
Luke Perry
2018-8-3
编辑:Luke Perry
2018-8-3
Hey Tomer,
Looking at your question I'm unsure which of the two you're looking for:
1: A kind of "heat map" where the color of the line in the plot depends on the peak values at a certain point, or magnitude of your sine curve in the plot. Obviously, you can change the parameter you're working with to match what you would want to judge the "heat" or color scheme of your plots. So, instead of magnitude, you could instead look at frequency of your sine waves, etc.
f=[10 50 100];
T=1./f;
%A list of colors from hot to cold.
colors={[1 0 0.1],[0.6 0 0.6],[0.1 0 1]};
for i=1:length(T)
t(i,:)=linspace(0,2*T(i),10000);
subplot(3,1,i);
y(i,:)=sin(2*pi*t(i,:).*f(i));
%Grab the magnitude, but if there is more than one maximum
%grab the first one. We only care about the number.
temp_magnitude=(max(y(i,:))-min(y(i,:)));
magnitudes(i)=temp_magnitude(1);
ax(i)=plot(t(i,:),y(i,:),'--');
title(sprintf('y=sin(2*pi*t*%d)', f(i)));
hold on;
end
%Normalize magnitudes.
normalizedmags=magnitudes/max(magnitudes);
%Arrange the normalized magnitudes by value (low to high)
arrangednormmags=sort(normalizedmags,'descend');
%Loop through the normalized mags and set the proper color
for i=1:length(normalizedmags)
ax(i).Color=colors{find(arrangednormmags,normalizedmags(i))};
end
2: How to loop through an assign different colors. Here's what I have for you.
clc;clear all;close all;
f=[10 50 100];
T=1./f;
%Make a list of colors. You can get creative with this
%and make a "smart" loop or array process of some kind to
%generate unique colors, or find some kind of tableau list.
colors={[0.15 0.7 0.1],[0 0 0],[0.7 0.2 0.03]};
for i=1:length(T)
t(i,:)=linspace(0,2*T(i),10000);
subplot(3,1,i);
y(i,:)=sin(2*pi*t(i,:).*f(i));
%Assign the color when plotting.
plot(t(i,:),y(i,:),'--','Color',colors{i});
title(sprintf('y=sin(2*pi*t*%d)', f(i)));
hold on;
end
4 个评论
Stephen23
2018-8-6
"To make black, combine all colors [1 1 1]."
Probably you meant [0,0,0].
"I have one question how did you transfer the colors in numbers ?"
Luke Perry
2018-8-6
Hey thanks Stephen. It was a little too early over here to be figuring that all out in my head.
另请参阅
类别
在 Help Center 和 File Exchange 中查找有关 Spectral Measurements 的更多信息
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!