Function With While Loop Help

5 次查看（过去 30 天）

显示更早的评论

Brian Peoples 2019-2-16

0
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/445353-function-with-while-loop-help

评论： Brian Peoples 2019-2-18

采纳的回答： Walter Roberson

在 MATLAB Online 中打开

Hello--

So I need to calculate time, flow rate, height, and velocity of water exiting a cylindrical container until the container is empty. I must use a while loop within a function to do so. I am supposed to break the loop once h (height) is slightly larger than 0 so h>0. I need to define a counting variable and start at t = 0.

This is my code for the function so far:

function [Q,h,t,V] = hw4_func_BDP(Initial_Height,Outer_D,Inner_D)
p = 1000;                    %(kg/m^3) pressure of water
g = 9.81;                    %(m/s^2) acceleration due to gravity
k = ((d^2)/(D^2))*sqrt(2*g); %constant with diameters of large hole vs exit hole
 
%Outputs (all vectors)
t = 0                        %Time
h = sqrt(h0-.5*k.*t).^2      %Fluid Height 
V = sqrt(2*g.*h)             %Velocity
Q = pi*(Inner_D/2)^2 .*V     %Flow Rate
 
j = 1
while h > 0
    %I am uncertain what to do here
    j = j+1
end

The inputs in my script are:

h0 = 2;                      %initial height
D = 1;                       %outer diameter
d = .1;                      %inner diameter

Also, I am supposed to calculate these as vectors, should I define them in my script as blank vectors before hand? Like t = [] h = [] V = [] Q = []

Please help!!

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

请先登录，再回答此问题。

采纳的回答

Walter Roberson 2019-2-17

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/445353-function-with-while-loop-help#answer_361360

At each step, you can determine h (height) by knowing the current volume remaining and knowing the cross-section area of the vessel. At each step, the volume reduces by the flow rate multiplied by the time step.

4 个评论
显示 2更早的评论隐藏 2更早的评论

Brian Peoples 2019-2-17

编辑：Walter Roberson 2019-2-18

在 MATLAB Online 中打开

function [Q,h,t,V] = hw4_func_BDP(Initial_Height,Outer_D,Inner_D)
%I got V by starting off with the Bernoulli's equation, crossing off
%pressure for the top and the bottom of the cylindrical container because the open drain causes it to equal
%zero, crossed out out the velocity on the top due to it being ostensibly
%zero (Because D>>d Vtop << Vbottom), crossed out density because it is the
%same all throughout the equation, then we are left with gh1 = 1/2 V2^2,
%therefore V2 is equal to sqrt(2gh).
 
%Constants
p = 1000;                                %(kg/m^3) pressure of water
g = 9.81;                                %(m/s^2) acceleration due to gravity
k = ((Inner_D^2)/(Outer_D^2))*sqrt(2*g); %constant with diameters of large hole vs exit hole
 
 
%Outputs for time, height, velocity,
%and flow rate in while loop
 
%Output Variables 
t = [0];
V = [0];
Q = [0];
if Initial_Height == 5
    h = 5;
else
    h = 2;
end
 
 
dt = 1;      %time step  
while h > 0
                     
t(1+dt) = t(dt) + 1;                              %time goes up by 1 each time
h(1+dt) = sqrt(Initial_Height-.5*k.*t(1+dt)).^2;  %Fluid Height 
V(1+dt) = sqrt(2*g.*h(1+dt));                     %Velocity
Q(1+dt) = pi*(Inner_D/2)^2 .*V(1+dt);             %Flow Rate
 
%dh for sanity check 
%dh
 
dt = dt+1;
end
%Last peramitors errasing when h is less than 0 and making the last time
%step equal to zero
h(dt) = 0
V(dt) = 0
Q(dt) = 0
end

So I was able to perform the while loop, but I am struggling on making a vector dh to watch the change in height after each time step. I do not want it to be directly related to the height, but more of a sanity check to make sure the loop is changing the height correctly. so not

dh = h(dt) - h(dt-1)

I know flow rate is given as:

Q = AV

My instructions say:

Use the flow rate to calculate how much water drained form the tank in the currenttime step and then use the area of the tank (not the exit hole) to calculate how much the height of the water change. You can call this vector dh.....