"measure temperature from i2c device using arduino hardware".

1 次查看（过去 30 天）
TAMALAMPUDI VENKATA SAI SAKETH REDDY
评论： Madhu Govindarajan 2019-3-27
HI, I am trying to read a data from tmp102 sensor with MATLAB by using arduino board. Here I am using I2C communication Before this I was able to read many sensor data with MATLAB by using arduino board with I2C communication. but for tmp102 sensor I am able to read the address and follow the data and write the required bytes, but when I read I am getting error "Failed to read 2 uint8 value(s) from the device." The code used is :
clear all clc a = arduino();
addrs = scanI2CBus(a)
tmp102 = i2cdev(a, '0x48')
write(tmp102, 0, 'uint8');
data = read(tmp102, 2, 'uint8');
temperature = (double(bitshift(int16(data(1)), 4)) + double(bitshift(int16(data(2)), -4))) * 0.0625
writeRegister(tmp102, 1, hex2dec('60B0'), 'uint16');
pause(0.25);
data = readRegister(tmp102, 0, 'int16');
temperature = double(bitshift(bitand(data, hex2dec('FFF8')), -3)) * 0.0625
writeRegister(tmp102, 1, hex2dec('60A0'), 'int16');
clear tmp102 a
Please help to resolve this issue. I am using MATLAB 2018b
Thanks saketh
  2 个评论
Walter Roberson
Walter Roberson 2019-3-23
You are not assigning to a.
Your line
clear all clc a = arduino();
is interpreted as a request to clear all, and clc, and a, and =, and arduino() . Some of that is not really valid syntax, but clear does not seem to care.
TAMALAMPUDI VENKATA SAI SAKETH REDDY
TAMALAMPUDI VENKATA SAI SAKETH REDDY 2019-3-26
编辑：TAMALAMPUDI VENKATA SAI SAKETH REDDY 2019-3-26
Iam using the code and connections which was given in the link provided by the mathworks https://www.mathworks.com/help/supportpkg/arduinoio/examples/measure-temperature-from-i2c-device-on-arduino-hardware.html?prodcode=ML .But Iam getting an error"Failed to read 2 uint8 value(s) from the device" when i running the code in the matlab version 2018b with arduino uno board.And while running the code Iam getting 0x0 empty cell array in the address place.Can you resolve the code and give the correct code.
thank you

请先登录，再进行评论。

请先登录，再回答此问题。

回答（3 个）

Madhu Govindarajan
Madhu Govindarajan 2019-3-20
What is the Arduino board using and does your hardware setup look similar to the one shown here - https://www.mathworks.com/help/supportpkg/arduinoio/examples/measure-temperature-from-i2c-device-on-arduino-hardware.html?prodcode=ML
  2 个评论
TAMALAMPUDI VENKATA SAI SAKETH REDDY
TAMALAMPUDI VENKATA SAI SAKETH REDDY 2019-3-21
almost same.we are using arduino uno board,tmp102 and connections are connected as mentioned above and the code is also same.But we are getting error "Failed to read 2 uint8 value(s) from the device.sir can u please give the solution for that.
Thanks for the previous response
Madhu Govindarajan
Madhu Govindarajan 2019-3-21
What happens if you remove the following three lines of code and run the rest of the code? -
write(tmp102, 0, 'uint8');
data = read(tmp102, 2, 'uint8');
temperature = (double(bitshift(int16(data(1)), 4)) + double(bitshift(int16(data(2)), -4))) * 0.0625

请先登录，再进行评论。

TAMALAMPUDI VENKATA SAI SAKETH REDDY
it was giving an error "failed to read int16 values from register 0".sir our project final review date was ahead. Can u please give the correct code to get output. Thank you for the response
Madhu Govindarajan
Madhu Govindarajan 2019-3-22
Can you try with other arduino boards or other sensors? That code works for me on the Arduino and TMP102 sensor.
  4 个评论
显示 2更早的评论
TAMALAMPUDI VENKATA SAI SAKETH REDDY
TAMALAMPUDI VENKATA SAI SAKETH REDDY 2019-3-27
I connected as per the given connections.Sir how can we know that whether the sensor is working or not. Thank you
Madhu Govindarajan
Madhu Govindarajan 2019-3-27
Try testing it from Arduino IDE itself and if that also does not work then you know the sensor is not working. If that works, reach out to MathWorks Technical Support.

请先登录，再进行评论。

类别

在 Help Center 和 File Exchange 中查找有关 MATLAB Support Package for Arduino Hardware 的更多信息

标签

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by