converting M-file into a block function in simulink

2012 8 15
3 个回答
回答已采纳
更新时间：2016 4 1
3 次查看（30 天）

0 个投票

hello can you show me how to move "file.m" into a function block in simulink thank you!

2 个评论
显示 无 隐藏 无

dong van duc
dong van duc 2012-8-15
I want to know all the "file.m" transformed into a block in "simulink"?

请先登录，再进行评论。

请先登录，再回答此问题。

 采纳的回答

Kaustubha Govind
Kaustubha Govind 2012-8-15
编辑：John Kelly 2015-2-26

0 个投票

You can call the function from any of three MATLAB Function blocks.

10 个评论
显示 8更早的评论 隐藏 8更早的评论

dong van duc
dong van duc 2012-8-15
thank you, I want to know all the "file.m" transformed into a block in "simulink"?
Kaustubha Govind
Kaustubha Govind 2012-8-16
You cannot "transform" it into a block exactly, but calling it from one of the aforementioned blocks will essentially do that.
dong van duc
dong van duc 2012-8-16
Thank you, I'll ask you later. Can you give me email?
Kaustubha Govind
Kaustubha Govind 2012-8-17
Sorry, we do not encourage sending personal messages. Please feel free to post any questions you run into on this forum though.
dong van duc
dong van duc 2012-8-21
I have a example "http://www.mathworks.com/matlabcentral/fileexchange/20431-dial", can you help me converter into a block in silulink
Kaustubha Govind
Kaustubha Govind 2012-8-21
Sorry, perhaps you could try following my advice and post back if you run into specific issues.
dong van duc
dong van duc 2012-8-22
I use a block "Level-2 M-file S-Function", M-file name = duong_truyen, I get a error: "Eroor due to multiple causes --> Too many input arguments.-->Error evaluating the initialization for M-S-Function 'duong_truyen'.Too many input arguments.The following is the MATLAB call stack (file names and line numbers) that produced this error:"
Kaustubha Govind
Kaustubha Govind 2012-8-22
Please start a new question and paste your code and the error message with the stack as well.
dong van duc
dong van duc 2012-8-23
编辑：dong van duc 2012-8-23
yes, I created a new question.

请先登录，再进行评论。

更多回答（2 个）

Youssef Haical
Youssef Haical 2014-9-5
编辑：Youssef Haical 2014-9-5

0 个投票

i made it but this answer is not clear ,,,, please try to show us just how we can add the initial values to run the simulink model without opening the command window and writing the values and then we run the simulink model
for example : i have this initial parameters : Pm=100e3; Flux=200; Ts=2e-5; p=2 ; N=2; f=50;
i need to make them inside of my simulink model without writing them in m-file or in command window
please help me
karishma kousar
karishma kousar 2016-4-1

0 个投票

hello sir i have a matlab code for face detection but i dont know how to do the simulink blocks,please any one can help me in this designing a simulink model for my matlab code

类别

在 帮助中心 和 File Exchange 中查找有关 Modeling 的更多信息

产品

标签

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by