Feeding knees angle to the walking robot

Question

Sizhe An 2019-6-30

0
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/469580-feeding-knees-angle-to-the-walking-robot

评论： Sizhe An 2019-8-9

Hi,

I'm doing gait analysis for human-being.

I watched a great video about how to build a walking robot and observe many metrics when the robot walking in this following link:https://www.mathworks.com/videos/matlab-and-simulink-robotics-arena-walking-robots-part-1-modeling-and-simulation-1505941655157.html

However, my target is in an opposite aspect. I recored the real knees degree data when people walking. Now I want to feed these degree data into the robot then observe how the robot walks. Is this possible?

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

请先登录，再回答此问题。

Answer 1

Sebastian Castro 2019-7-1

2
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/469580-feeding-knees-angle-to-the-walking-robot#answer_381425

Thanks for tagging this post with roboticsarena so we got that notification! Much appreciated.

In Simscape Multibody, you can choose to actuate joints either with torques or with motion profiles. I am guessing you want to put in a motion profile from the real knee angle data. See the "Motion Input" section below.

https://www.mathworks.com/help/physmod/sm/ug/joint-actuation.html

Or, this example:

https://www.mathworks.com/help/physmod/sm/ug/prescribe-joint-motion-in-four-bar-model.html

- Sebastian

5 个评论
显示 3更早的评论隐藏 3更早的评论

Sebastian Castro 2019-7-4

That's right. The heavier the robot, the higher the stiffness needs to be... else it might fall through.

You should pick something big enough to hold the weight at a specified displacement (much smaller than the thickness of the foot).

Force = Stiffness*Displacement

For more information, see here:

https://blogs.mathworks.com/racing-lounge/2017/09/12/introduction-to-contact-modeling/

Sizhe An 2019-8-9

one_hip_leg.slx

Hi Sebastian,

I kind of modify the four bar through revolute joints to a easy robotic lower lambs. And I give the input angles to the leg then observe how it works. It turns out it works very well and now I want to add one more legs but I got stuck.

As shown in Fig.1, l1 is the hip and l2 is the leg. This is exactly the model I wanna build. α and β I got from sensors, which is the input. I wanna observe how l1 and l2 rotates when α, β is changing.

However, as shown in Fig.2, I can only build one hip and leg here. I have no idea how to add another lamb on the same pivot mount. I have a look in https://ww2.mathworks.cn/help/physmod/sm/ug/model-four-bar.html but it doesn't help much...

My design file is attached. Can you please give me an idea how I can make the model I want?

Thank you very much!!

请先登录，再进行评论。

Feeding knees angle to the walking robot

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

采纳的回答

5 个评论
显示 3更早的评论隐藏 3更早的评论

更多回答（0 个）

另请参阅

类别

标签

产品

Community Treasure Hunt

Feeding knees angle to the walking robot

0 个评论 显示 -2更早的评论隐藏 -2更早的评论

采纳的回答

5 个评论 显示 3更早的评论隐藏 3更早的评论

更多回答（0 个）

另请参阅

类别

标签

产品

Community Treasure Hunt

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

5 个评论
显示 3更早的评论隐藏 3更早的评论