Plotting two contourf plots on the same plot

2020 6 20
2 个回答
回答已采纳
更新时间：2021 9 24
11 次查看（30 天）

0 个投票

Hello,
I am trying to plot two data matrices on the same plot. However, I do not know how to adjust the transparancy of one of the plots.
The code is shown below with the attached data of Z1 and Z2.
If I try to plot the on top of each other just like the code of figure (3), the data values of the Z1 will not fully be visible since the Z2 data will be on top of it.
Is there a way to adjust the transparency of the plotted Z2 data so that the the full Z1 data will be visible?
And, is there a possibility to change the color of each contourf plot?
Thank you for your time,
Elie Hatem
clear all;clc;
x=-pi:0.1:pi;
y=x;
[X,Y]=meshgrid(x,y);
load('motorization_data.mat','Z1','Z2')
figure(1)
contourf(X,Y,Z1,[0 0])
figure(2)
contourf(X,Y,Z2,[0 0])
figure(3)
contourf(X,Y,Z1,[0 0])
hold on
contourf(X,Y,Z2,[0 0])
hold off

5 个评论
显示 3更早的评论 隐藏 3更早的评论

Elie Hatem
Elie Hatem 2020-6-20
Thank you for your response.
If I try to run the code bellow I get the following error:
Error using alpha (line 68)
Wrong number of arguments
Error in untitled (line 8)
alpha(j,0.1)
Maybe alpha is not supported for contourf plots?
clear all;clc;
x=-pi:0.1:pi;
y=x;
[X,Y]=meshgrid(x,y);
load('motorization_data.mat','Z1','Z2')
figure(1)
j=contourf(X,Y,Z1,[0 0])
alpha(j,0.1)
Elie Hatem
Elie Hatem 2020-6-21
Yes, I saw this link prior to asking my question.
I tried to use "fill". However, my plot was not plotting as desired.
I solved the problem by removing the columns which have zero elements in the X axis since it was clear that neither their X (which is zero) and their Y (belonging to the zero in the X) are part of the data. They were introduced when taking contourf was used. Moreover, the code below solved my problem:
figure(3)
j=contourf(X,Y,Z1,[0 0]);
hold on
contourf(X,Y,Z2,[0 0])
hold off
% Removing the unwanted values from j
i=0;
while (1)
l_j=length(j);
i=i+1;
if i==143
disp('i=143')
end
if j(1,i)==0
j(:,i)=[];
l_j=l_j-1;
end
if i==l_j
break;
end
end
%%
xi = j(1,:);
yi = j(2,:);
% Contour plot
figure(4)
contourf(X,Y,Z2,[0 0 ]);
% Transparent patch
hold on
fill(xi,yi,'m','FaceAlpha',0.5,'LineWidth',1);
hold off

请先登录，再进行评论。

请先登录，再回答此问题。

 采纳的回答

Elie Hatem
Elie Hatem 2020-6-21

0 个投票

I solved the problem by removing the columns which have zero elements in the X axis since it was clear that neither their X (which is zero) and their Y (belonging to the zero in the X) are part of the data. They were introduced when taking contourf was used. Moreover, the code below solved my problem:
figure(3)
j=contourf(X,Y,Z1,[0 0]);
hold on
contourf(X,Y,Z2,[0 0])
hold off
% Removing the unwanted values from j
i=0;
while (1)
l_j=length(j);
i=i+1;
if i==143
disp('i=143')
end
if j(1,i)==0
j(:,i)=[];
l_j=l_j-1;
end
if i==l_j
break;
end
end
%%
xi = j(1,:);
yi = j(2,:);
% Contour plot
figure(4)
contourf(X,Y,Z2,[0 0 ]);
% Transparent patch
hold on
fill(xi,yi,'m','FaceAlpha',0.5,'LineWidth',1);
hold off

更多回答（1 个）

Long Hoang Van
Long Hoang Van 2021-9-24

0 个投票

clear all;clc;
x=-pi:0.1:pi;
y=x;
[X,Y]=meshgrid(x,y);
load('motorization_data.mat','Z1','Z2')
figure(1)
contourf(X,Y,Z1,[0 0])
figure(2)
contourf(X,Y,Z2,[0 0])
figure(3)
contourf(X,Y,Z1,[0 0])
hold on
contourf(X,Y,Z2,[0 0])
hold off

类别

在 帮助中心 和 File Exchange 中查找有关 Contour Plots 的更多信息

产品

版本

R2020a

标签

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by