Image Acquisition Camera - High Speed - Fast Capture

13 次查看（过去 30 天）
Jeremy
Jeremy 2013-2-11
评论： Walter Roberson 2018-1-5
Hello,
I am using Matlab 2012 with Image Acquisition Toolbox 2012.
I am using a generic webcam (Logitech Sphere AF) with the command
frame=getsnapshot(obj);
for image capture with the following default properties:
% % Device Specific Default Properties:
% BacklightCompensation = on
% Brightness = 128
% Contrast = 32
% Exposure = -7
% ExposureMode = auto
% Focus = 0
% FocusMode = auto
% FrameRate = 30.0000
% Gain = 0
% HorizontalFlip = off
% Pan = 0
% Saturation = 32
% Sharpness = 224
% Tilt = 0
% VerticalFlip = off
% WhiteBalance = 4000
% WhiteBalanceMode = auto
I am trying to find a faster camera model and property settings, if possible on a usb connection.
Does anyone have any suggestions for a specific camera model and associated manually configured properties settings for maximum frame capture speed?
Best, Jeremy

请先登录，再回答此问题。

采纳的回答

Thomas
Thomas 2013-2-23
编辑：Walter Roberson 2013-2-23
Jeremy,
We use the Thorlabs CMOS camera and get frame rates of several hundred Hertz using mex files, for regions of interest of 32 x 32 pixels. There is some memory management involved, and we use separate mex files for opening the camera (once per session), grabbing a frame, and closing the camera (once per session). We also have a mex file for setting the pixel clock, the exposure, and the frame rate. I don't promise it will work for you, but I've posted the files for the time being here, along with the code required to create the mex files and a demo m-file that tests it all out.
http://www.bifanofamily.com/Thorlabs_cam.zip
By the way, we also do SLM compensation through scattering media! Good luck.
  7 个评论
显示 5更早的评论
Walter Roberson
Walter Roberson 2018-1-5
Chris Stockbridge mentioned a File Exchange contribution; did you give that a try?

请先登录，再进行评论。

更多回答（4 个）

Chris Stockbridge
Chris Stockbridge 2015-10-20
All of the files for working with the Thorlabs DCx series of cameras can now be found on the MATLAB file exchange here: Thorlabs DCx
Walter Roberson
Walter Roberson 2013-2-11
David Tarkowski
David Tarkowski 2013-2-11
Your question is a little vague, but I think that this example should help you out.
Jeremy
Jeremy 2013-2-11
Thank you for your response,
I am imaging the speckle pattern of light scattered through tissue from the beam output of a spatial light modulator for an adaptive optics experiment.
The modulator is controlled by an lcd with a frame rate of ~60Hz. I am trying to setup frame capture at this speed (~60Hz ; elapsed time 0.05 sec) or faster if possible. The decorrelation time constant for the tissue is 3-4secs so every little bit helps.
One option is to buy a Thorlabs DCC1545M and play with the mex interface(from previous thread below)
http://www.mathworks.com/matlabcentral/answers/35918
which is tricky but should enable optimization of device properties to achieve a faster frame rate.
I am searching for some specific cmos usb devices which have been shown to work with Matlab that have faster hardware performance than the above devices.
Jeremy

类别

在 Help Center 和 File Exchange 中查找有关 MATLAB Support Package for IP Cameras 的更多信息

标签

产品

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by