how to change simulink block properties from matlab pogram?

Question

Harish Balaga 2013-5-15

0
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/75817-how-to-change-simulink-block-properties-from-matlab-pogram

I have created a simulink model in which there are two 3-phase fault blocks. i want to change the fault block properties (like faulty phase, fault resistance..etc) from matlab program (m file) and run the model.. How to do that?

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

请先登录，再回答此问题。

Answer 1

Harish Balaga 2013-5-15

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/75817-how-to-change-simulink-block-properties-from-matlab-pogram#answer_85511

在 MATLAB Online 中打开

I found the answer myself from matlab help. it can be set or reset using "set_param" command. an example is given below

open('MyModel.mdl');
set_param('MyModel/3-Phase Fault', 'FaultA', 'on');

here "3-Phase Fault" is the name i gave to the block in "MyModel.mdl". "FaultA" is the parameter name (Default). To check the type & name the of parameter (checkbox in my case, so on & off are the parameter values), one may use the following command to open the model in editable code form.

edit('MyModel.mdl');

and then search for the block name.

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

Answer 2

Valmir Sadiku 2013-5-15

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/75817-how-to-change-simulink-block-properties-from-matlab-pogram#answer_85481

在 MATLAB Online 中打开

Hello,

One possible way are that you use parameter in your 3-phase fault block. Then write an M-File in which you can generate/change the values of this parameter (which are now stored in the Workspace) and open the Simulink model from matlab with the command:

results = sim('myFaultyModel');

regards V.Sadiku

3 个评论
显示 1更早的评论隐藏 1更早的评论

Valmir Sadiku 2013-5-15

在 MATLAB Online 中打开

as i already wrote above you can modify your parameter on the M-File simply, e.g. :

parameter_1  =  12.1;
parameter_2 = 1.05;
......
parameter_x = 0.1;
..

now you can the call the model, which runs with changed parameter values

sim('myFaultyModel');

then maybe with another parameter again:

parameter_1  =  12.8;
parameter_2 = 1.0;
......
parameter_x = 0.18;
..

and call the model again and so on.

Harish Balaga 2013-5-15

在 MATLAB Online 中打开

thank you for the answer but it seems you didn't get my question clearly. What is the name of the phase A, B, C values of the 3-phase fault block of the model? how to know that? How to set (tick mark) or reset the check box of each phase through program? is there any syntax like

faultmodel.faultblock1.phaseA=1; %to set

and after some time

faultmodel.faultblock1.phaseA=0; % to reset

??

i need to check or uncheck the check box in the properties window (window that appears when we double click on any block in Simulink) of the fault block

请先登录，再进行评论。