Difference between switch and if

364 次查看（过去 30 天）
Bob Thompson
Bob Thompson 2021-4-21
评论： Bob Thompson 2021-4-21
I just ran across switch being used in a code and am wonder how it differs from if. The use of switch may not have been well set up in the code I was looking at, because they look generally the same. I did not read the documentation in great detail, just enough to get an idea of what switch does.
  2 个评论
Jonas
Jonas 2021-4-21
i think in matlab there is no difference between switch and many if/elseif statements. the switch is also known in many other programming languages, but behaves a bit differently than in matlab. in matlab the corresponding case is executed and the code continues behind the block, in other languages the switch block is exited only if there is a break at the end of the case, otherwise other cases would be tested too. i hope i remebered correctly, it has been some time since my last c++ session
Bob Thompson
Bob Thompson 2021-4-21
Thanks, it's good to know I should keep an eye out for this in other languages.

请先登录，再进行评论。

请先登录，再回答此问题。

采纳的回答

Adam Danz
Adam Danz 2021-4-21
编辑：Adam Danz 2021-4-21
if/elseif/else is quite similar to switch/case/otherwise. Both provide a default action when no conditions are met (else & otherwise) and you're encouraged to use those options. In Matlab, both sets of tests stop execution once a condition is met (in some other languages all cases are executed when there are multiple case matches). I doubt either approach has a computationally efficient beneifit over the other.
Here are some of their differences.
  • When there are multple conditions, switch/case/otherwise is often the more organized approach resulting in more readable code. It often reduces the need to use operators and functions to test each condition. For example, when testing string matches, if/elseif/else requires using a string comparson function such as strcmp/i, ismember, etc or an operator (==) for strings while a switch/case/otherwise just uses a string for each case and if case sensitivity should be ignored, the switch statement could use upper/lower to force the sting to upper or lower case while each case-condition contains the same letter-case.
  • switch/case/otherwise is easier to lay out when conditions all rely on the same class such as testing matches to strings, categories,enumerated values but if/elseif/else can be easier to write and read with mixed classes or complex condition tests such as ranges of values. Note that both sets of tests can use expressions or call functions in Matlab but it can become unpleasent to design and read using switch/case/otherwise.
Which is more readable for you (ignore that these can likely be vectorized)?
% Example 1
country = 'Croatia';
switch lower(country)
case 'albania'
y = ...
case 'bosnia'
y = ...
case 'croatia'
y = ...
case 'slovenia'
y = ...
otherwise
error('Country not listed: %s', country)
end
if strcmpi(country,'Albania')
y = ...
elseif strcmpi(country,'Bosnia')
y = ...
elseif strcmpi(country,'Croatia')
y = ...
elseif strcmpi(country,'Slovenia')
y = ...
else
error('Country not listed: %s', country)
end
x = pi;
switch true
case x>0 && x<=1
y = ...
case x>1 && x<=2
y = ...
case x>2 && x<=3
y = ...
case x>3 && x<=4
y = ...
otherwise
y = . . .
end
if x>0 && x<=1
y = ...
elseif x>1 && x<=2
y = ...
elseif x>2 && x<=3
y = ...
elseif x>3 && x<=4
y = ...
else
y = . . .
end
Also see

更多回答（1 个）

Image Analyst
Image Analyst 2021-4-21
They're pretty much the same, just slightly different syntax as to how to get the condition. Switch requires an extra line of code than if but that's no big deal.
switch(value)
case 1
% code
otherwise
% code
end % 4 lines of code
if value == 1
% code
else
%code
end % 3 lines of code
Use which ever one you think makes it easier to read your code. If the condition needs to be made up from multiple tests/operations, then it might be better in an if. switch is best for situations where the condition is just a single value (number, string), or cell array of several such values.
value = (blah + fubar) * snafu
switch(value)
case 1
% code
case {2, 3}
% code
otherwise
% code
end
if (blah + fubar) * snafu == 1
% code
elseif (blah + fubar) * snafu == 2 && (someOtherVariable == 3) % Hard to do with "case"
% code
end
My two cents worth, for what it's worth.
  1 个评论
Bob Thompson
Bob Thompson 2021-4-21
Thanks, I appreciate the different perspective from how others described it.

请先登录，再进行评论。

类别

在 Help Center 和 File Exchange 中查找有关 Testing Frameworks 的更多信息

标签

产品


版本

R2019b

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by