problem with F28379D

14 次查看（过去 30 天）
SALAH alatai
SALAH alatai 2021-4-22
评论： Walter Roberson 2022-4-25
Hello , I am trying to give simple pulse output to GPIO to blink LED in F28379D Launchpad, but it dose not working.
and recevied this messge.
How to solve this issue? I am using MATLAB 2020A.
thanks in advance.
The following error occurred during deployment to your hardware board:
Debug Server Scripting (DSS) error:
*** User inputs:
Target Configuration: undefined
Program Name: undefined
Board Name: unspecified (connect to first board)
CPU Name: unspecified (connect to first CPU)
Hardware Name: unspecified
*** Starting debug session...
SEVERE: Cannot read System Setup data from XML file C:\Users\User\MATLAB\Micro_controller_ert_rtw\undefined
Error parsing file:
Fatal Error at (0, 0): An exception occurred! Type:RuntimeException, Message:The primary document entity could not be opened. Id=C:\Users\User\MATLAB\Micro_controller_ert_rtw\undefined
SEVERE: Could not start server: DebugServer.1: Cannot read System Setup data from XML file C:\Users\User\MATLAB\Micro_controller_ert_rtw\undefined
Error parsing file:
Fatal Error at (0, 0): An exception occurred! Type:RuntimeException, Message:The primary document entity could not be opened. Id=C:\Users\User\MATLAB\Micro_controller_ert_rtw\undefined
*** Cannot create a valid debug session for Board/CPU=*/*.
Make sure this matches only one board and one CPU.
Exiting...
  16 个评论
显示 14更早的评论
Moise Cristi
Moise Cristi 2021-12-26
I did it but I still have the same problem. Can you contact me on email or on fb to help me, please! I dont know what I m doing wrong. (cristimoise_14@yahoo.com)
Thank you!

请先登录，再进行评论。

请先登录，再回答此问题。

采纳的回答

SALAH alatai
SALAH alatai 2021-4-27
The problem was with the latest versions of CCS (10.30), after install the oldest version 10.2 no problem and the F28379D Launchpad is working.
  7 个评论
显示 5更早的评论
abdelhak boudallaa
abdelhak boudallaa 2022-4-25
Hello doctor;
I used matlab 2018a CCS10.2, and always I have this problem of cofiguration of F28379D launchpad.
can you help me solve this problem?
C:\Users\ADL\Desktop\these mod\Projet_Master\commande_vectorielle_PWM_V7_ert_rtw>exit /B 0
Downloading program to the target hardware...
### Build procedure for model: 'commande_vectorielle_PWM_V7' aborted due to an error.
The following error occurred during deployment to your hardware board:
Debug Server Scripting (DSS) error:
*** User inputs:
Target Configuration: C:\PROGRA~3\MATLAB\SUPPOR~1\R2018a\toolbox\target\SUPPOR~1\tic2000/CCS_CO~1/F28379~1.CCX
Program Name: C:\Users\ADL\Desktop\THESEM~1\PROJET~1\COBFCB~1.OUT
Board Name: *
CPU Name: C28xx_CPU1
Hardware Name: TI_Delfino_F2837xD
*** Starting debug session...
SEVERE: IcePick_C_0: Error connecting to the target: (Error -151 @ 0x0) One of the FTDI driver functions used during the connect returned bad status or an error. The cause may be one or more of: no XDS100 is plugged in, invalid XDS100 serial number, blank XDS100 EEPROM, missing FTDI drivers, faulty USB cable. Use the xds100serial command-line utility in the 'common/uscif' folder to verify the XDS100 can be located. (Emulation package 8.1.0.00012)
SEVERE: emulation failure occurred
SEVERE: Error connecting to the target: emulation failure occurred
*** Cannot create a valid debug session for Board/CPU=*/C28xx_CPU1.
Make sure this matches only one board and one CPU.
Exiting...
Walter Roberson
Walter Roberson 2022-4-25
@abdelhak boudallaa
Did you try using the xds100serial command-line utility in the 'common/uscif' folder to check whether the XDS100 can be located?

请先登录，再进行评论。

更多回答（0 个）

类别

在 Help Center 和 File Exchange 中查找有关 Texas Instruments C2000 Processors 的更多信息

标签

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by