How do I call BLOCKPROC with more than one input image?

Question

Sukuchha 2013-10-8

1
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/89516-how-do-i-call-blockproc-with-more-than-one-input-image

评论： Image Analyst 2013-10-15

i have two images,and have a function which requires 3x3 sliding window data from both image A and image B. Is there a way to get it done with blockpro function. Any hint would be useful.

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

请先登录，再回答此问题。

Answer 1

Image Analyst 2013-10-8

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/89516-how-do-i-call-blockproc-with-more-than-one-input-image#answer_98976

See demos attached below.

4 个评论
显示 2更早的评论隐藏 2更早的评论

Sukuchha 2013-10-15

its because the result of the function depends on both 3x3 blocks of both image A and image B. I finally managed to get around with combining images like cat)3, imageA, imageB). then using blockproc with combine image. In the functin i have extracted imageA and imageB part to proceed with further processing. thx.

Image Analyst 2013-10-15

Sounds sort of complicated. What type of image are A and B? If they're color then you have 6 color channels on the cat'ed array, if they're grayscale, then you have 2. Usually image processing works with 1 or 3 color channels, not 2 or 6, so I'd be careful that it's doing what you expect. Why would you not do it like I said where you do it on A and then do it on B and then combine the results? That seems much more straightforward and less risky.

请先登录，再进行评论。

Answer 2

Ashish Uthama 2013-10-10

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/89516-how-do-i-call-blockproc-with-more-than-one-input-image#answer_99245

编辑：Ashish Uthama 2013-10-10

在 MATLAB Online 中打开

Have a look at the Definitions section of the blockproc doc. Consider using the 'location' and 'blockSize' fields to index into the second variable.

>> im1 = ones(10);
>> im2 = ones(10)*2;
>> type myfun.m
function o = myfun(bs, im2)
im1Block = bs.data;
startInd = bs.location;
endInd   = bs.location+bs.blockSize-1;
im2Block = im2(startInd(1):endInd(1), startInd(2):endInd(2));
o = im1Block+im2Block;
end
% This is the tricky part. Here, all of im2 gets 'snapshot'ed inthe function handle, so its available inside myfun when called via funcHandle inside blockproc (!).
>> funcHandle = @(bs)myfun(bs,im2);
>> blockproc(im1,[5 5],funcHandle)
ans =
       3     3     3     3     3     3     3     3     3     3
       3     3     3     3     3     3     3     3     3     3
       3     3     3     3     3     3     3     3     3     3
       3     3     3     3     3     3     3     3     3     3
       3     3     3     3     3     3     3     3     3     3
       3     3     3     3     3     3     3     3     3     3
       3     3     3     3     3     3     3     3     3     3
       3     3     3     3     3     3     3     3     3     3
       3     3     3     3     3     3     3     3     3     3
       3     3     3     3     3     3     3     3     3     3
>>

1 个评论
显示 -1更早的评论隐藏 -1更早的评论

Sukuchha 2013-10-15

hi , i never knew ther is location properties. cheers. But i just combine mz images and extract part of imageA and imageB in my function handle for blockproc. thx.

请先登录，再进行评论。