Feeds
提问
Power Supply current output for data analysis
Hello, We have many power supplies that have been running for the past 15 years. I have access to the power supply output curre...
2 years 前 | 1 个回答 | 0
1
个回答提问
Importing data from a .mat file into the Sensitivity Analyzer App on Simulink
I have a .mat file that has data that I would like to import into the Sensitivity Analyzer app on simulink to perform additional...
2 years 前 | 1 个回答 | 0
1
个回答提问
Capturing efficiency of a system while sweeping voltages and duty cycle parameters
I have a simscape simulation model of a power electronics converter and I need to find the optimum parameters to achieve the bes...
2 years 前 | 1 个回答 | 0
1
个回答提问
Modeling RG220 coaxial cable using a PI section line
I have two parallel RG-220/u coaxial cables which go to a magnet load from a pulse forming network. I recently found out that I ...
2 years 前 | 1 个回答 | 0
1
个回答提问
Extracting amplitude and frequency component using short time Fourier transform
I need to calculate the capacitance and equivalent series resistance (ESR) of a capacitor in a Boost converter. My boost convert...
2 years 前 | 1 个回答 | 0
1
个回答提问
Three-phase, three-winding transformer parameters
How to calculate the following values in a three-phase, three-winding transformer? I need to model this transformer in MATLAB/Si...
2 years 前 | 1 个回答 | 0
1
个回答提问
How to create a square wave with different amplitudes?
I need to generate a square wave from -8 to 15 with a frequency of 18 kHz. How can I do this in Simulink?
2 years 前 | 1 个回答 | 0
1
个回答提问
RC snubbers for 12-pulse thyristor bridge
I am trying to simulate an AC-DC power supply (12-pulse thyristor bridge connected in series) with an RC snubber. The real power...
3 years 前 | 0 个回答 | 0
0
个回答提问
Step Down Solar PV High DC Voltage
I have a PV panel which is rated at 5HP. The DC voltage generated by the panel is connected to the DC bus of its respective AC d...
4 years 前 | 0 个回答 | 0
0
个回答提问
Computing voltage and current amplitude and average power
Hello, I have three sinusoidal waveforms namely, voltage, current, and power acquired using an oscilloscope which I then have c...
4 years 前 | 1 个回答 | 0
1
个回答提问
How to model a Klystron in Matlab/Simulink?
Hello all, I am trying to model a Klystron which is a specialized linear-beam vacuum tube that is used as an amplifier for high...
5 years 前 | 0 个回答 | 0
0
个回答提问
How should the change in delta V (change in voltage) look like in a perturb and observe algorithm?
Hello all, I am currently working on an IEEE paper which is about extracting maximum power under partial shading of PV panels...
6 years 前 | 0 个回答 | 0
0
个回答提问
How do I plot this graph on MATLAB?
Dear all, I am having difficulty in plotting this particular graph on MATLAB. I know that I am supposed to use an if and/or f...
6 years 前 | 1 个回答 | 0
1
个回答提问
How to create a Network Node Incidence Matrix?
Hello guys, I am currently working on an IEEE paper which uses the Data of an IEEE-24 Bus System. I need to construct a Network...
6 years 前 | 2 个回答 | 0
2
个回答提问
How to reduce the size of a 144x1 Vector to a 72x1 Vector by adding two consecutive elements in the Original Vector?
Hello all, I have a vector which has the dimensions of 144x1. The numbers in the vector repeat after every sixth row. For examp...
7 years 前 | 1 个回答 | 0