提问
how to open figure one simulink
how make bock of m-file which contain figure and open it on simulink remark: simulink is on line (time inf)
12 years 前 | 1 个回答 | 0
1
个回答提问
figure
how to move line in a figure continuously by which one of its ends fixed at zero and the ling move around zero
12 years 前 | 1 个回答 | 0
1
个回答提问
signal processing managment
if i have signal how can i obtain its peak frequency in array if my time is inf
12 years 前 | 0 个回答 | 0
0
个回答提问
communication system
in fm-cw radar i use saw tooth ans sweep of freq when i sweep frequency the reflected signal with the same frequency but shifted...
12 years 前 | 1 个回答 | 0
1
个回答已提交
Developed FM-CW Radar approach
this project correct the error which occur in the previous project
12 years 前 | 3 次下载 |
提问
I/O interface
what are the I/O ports available which i can use it to make real time system e.g: analog signal needed to be processed by matl...
12 years 前 | 0 个回答 | 0
0
个回答提问
simulink
if i have a simulink model and the output of low pass filter is sin signal with certain frequency if i want to know this frequen...
12 years 前 | 2 个回答 | 0
2
个回答
提问
signal processing frequency estimation
if i have a simulink model and the output of low pass filter is sin signal with certain frequency if i want to know this frequen...
12 years 前 | 0 个回答 | 0
0
个回答已回答
Radar System
okey, chirp signal can be generated from vco block in comm.block set drived by saw tooth from signal genrator in source block ...
Radar System
okey, chirp signal can be generated from vco block in comm.block set drived by saw tooth from signal genrator in source block ...
12 years 前 | 0
提问
gui
hello, i need any information bout gui because i ammaking radar system with scope
12 years 前 | 2 个回答 | 0
2
个回答提问
can this program improved
hello, i make frequency modulated continouse wave radar using simulink <http://www.mediafire.com/?10kw7vsdfpo7rrs>
12 years 前 | 0 个回答 | 0
0
个回答已回答
How to continously run and display the simulink results ?
you can adjust simulation time to inf then use your scope you can watch your signal
How to continously run and display the simulink results ?
you can adjust simulation time to inf then use your scope you can watch your signal
12 years 前 | 2
| 已接受
提问
frequency estimation
i make fmcw radar and the output of mixer will be connected to the mic socket in my labtop then i use simulink to calculate rang...
12 years 前 | 1 个回答 | 0
1
个回答提问
simulink &m-file
i have m-file code and a simulink model can i convert m-file code to block in simulink which i can make its input port a sinus...
12 years 前 | 1 个回答 | 0
1
个回答提问
data analysis
if i have array x and i want to get the index of maximum value of it ex:x=[1 2 3 4 5 0 11] i want command which give me that ...
12 years 前 | 1 个回答 | 0
1
个回答提问
simulik
need block its input a signal and its output is frequency of signal
12 years 前 | 1 个回答 | 0
1
个回答提问
simulinke with m-file
can i make interface between a simulink file and m- file ? simulink the op signal is sin and i need m-file to calculate frequen...
12 years 前 | 1 个回答 | 0
1
个回答提问
simulink
if i have a signal in simulink and i want to calculat frequency what can i do?
12 years 前 | 1 个回答 | 0
1
个回答提问
system failure
i used simulink : i used audio device to acquiring data from mic then make some processing and drive it by speaker after that m...
12 years 前 | 0 个回答 | 0
0
个回答提问
data transfer
i take data from audio micin simulink and i want to make some processing for data in m file
12 years 前 | 0 个回答 | 0
0
个回答提问
labview data connection
hello,how to transfer data from simulink to labview and if it can not be done i want to make radar scope on simulink
12 years 前 | 0 个回答 | 0
0
个回答提问
simulink rf receiver
can i make rf radio operate at 1 mhz in simulink when antenna is connected to microphone audio device
12 years 前 | 0 个回答 | 0
0
个回答已回答
GUI BUTTON
you can make this operation by visual basic then use data interface to complete your design on matlab
GUI BUTTON
you can make this operation by visual basic then use data interface to complete your design on matlab
12 years 前 | 0
提问
real time
can simulink deal with audio signal which have frequency 10khz? and why simulink doesn't run normally in high freqeuncy ? i.e ...
12 years 前 | 0 个回答 | 0
0
个回答提问
fm-cw radar
this is the code of rx of fm-cw radar to get beat frequency is this correct? %receiver of fm-cw radar clear all;clc;cl...
13 years 前 | 0 个回答 | 0