photo

Charanraj


自 2013 起处于活动状态

Followers: 0   Following: 0

消息

I am an Master student.

统计学

  • First Review
  • First Answer

查看徽章

Feeds

排序方式:

已回答
Can't set capacitor initial voltage of cap because of powergui error
Hi Shashwat, Thanks for your comment. I have tried the steps in the shared link. But it did not work. So, I have attached my ...

4 years 前 | 0

提问


Unable to initialise capacitor voltage
Hello, I have a very simple circuit taken from simscape library in simulink. My circuit is made of a definite gain opamp, a ca...

4 years 前 | 1 个回答 | 0

1

个回答

已回答
how to resolve the 'dot indexing not supported for this type of variable' error when creating GUIs with GUIDE?
I got a similar error of Dot indexing. But unable to find loop where the error exists :( I have attached a pic that tells about ...

4 years 前 | 0

已回答
Too many output arguments in 'project' command :(
Yes, I have to define a function to use it. Thanks for your comments :)

6 years 前 | 0

提问


Too many output arguments in 'project' command :(
Hey i just try to do Xproj = project(Xm, Wpca(:,1:2)) where Xm & Wpca are 178*13 double type vectors. I get error 'Too...

6 years 前 | 1 个回答 | 0

1

个回答

已回答
Need to find the distribution from mean & standard deviation
Thank you all for your answers. Finally, I managed to tune something near to the desired mean & std. Yes, I was looking for the ...

6 years 前 | 0

提问


Need to find the distribution from mean & standard deviation
Hello, I need a 100 numbers of distribution for a specified mean & std. I found one, but its not accurate. The one I found is...

6 years 前 | 3 个回答 | 0

3

个回答

提问


Single sided amplitude FFT
For a normal FFT analysis, I can do directly from the scope. But how to do for a single-sided amplitude FFT directly in simulink...

9 years 前 | 0 个回答 | 0

0

个回答

已回答
Plot single-sided amplitude spectrum.
hey, can a single sided FFT taken directly from the scope by using an absolute block before the scope ?

9 years 前 | 0

提问


PI controller and an integrator.
Hi, I am using a discrete control algorithm to control an inverter. In this I have to construct a PI controller and an integr...

9 years 前 | 0 个回答 | 0

0

个回答

已回答
Having a Simulink error while simulating a UAV to track a UGV.
hey I have the same problem. I n my case the feedback is a single number and when I put an unit delay, it converts to 3 numbers...

9 years 前 | 0

已回答
An error in the sum of three signal
Seems adding a memory makes more complications, which I have attached in the picture. And there are many unit delay blocks. Whic...

9 years 前 | 0

已回答
An error in the sum of three signal
<</matlabcentral/answers/uploaded_files/24948/Capture.JPG>>

9 years 前 | 0

提问


An error in the sum of three signal
I just use sum of three signals and i get an error like this. Can you help to rectify this error ?

9 years 前 | 3 个回答 | 0

3

个回答

提问


Pulse generation from duty cycles in Space vector modulation
hi, I have duty cycle values d1, d2 & d3 for a 3 level Neutral Point Converter. Now how to generate 12 pulses for it using th...

10 years 前 | 0 个回答 | 0

0

个回答

提问


How to clear this Error :In an assignment A(I) = B, the number of elements in B and I must be the same
In the below hexagon figure, the parallelogram of coordinate (g,h) is the base plane on which I am working on. In this plane ...

10 years 前 | 0 个回答 | 0

0

个回答

提问


In an assignment A(I) = B, the number of elements in B and I must be the same
I have written a simple Matlab s-function program to calculate nearest coordinates in a parallelogram, . the code is as follows:...

10 years 前 | 0 个回答 | 0

0

个回答

已回答
In an assignment A(I) = B, the number of elements in B and I must be the same.
I too get the same error.I have written a simple Matlab s-function program to calculate nearest coordinates in a parallelogram, ...

10 years 前 | 0