![photo](/responsive_image/150/150/0/0/0/cache/matlabcentral/profiles/7819417_1537384380650_DEF.jpg)
Matthew Mishrikey
Followers: 0 Following: 0
Feeds
提问
variables with scope local to subsystem
I'm a bit confused about variable scope. I think I know what's going on but am looking for confirmation and maybe advice on th...
2 years 前 | 1 个回答 | 0
1
个回答已回答
Radio Button Mask for Simscape Block
I figured out a way. I saw a snippet of code in one of the videos on the topic, and it gave me enough clues to write a callback...
Radio Button Mask for Simscape Block
I figured out a way. I saw a snippet of code in one of the videos on the topic, and it gave me enough clues to write a callback...
2 years 前 | 0
| 已接受
提问
Radio Button Mask for Simscape Block
I have a stock Simscape block (Cauer Element) that has two parameters - Resistance and Tau. I am trying to add a mask to modify...
2 years 前 | 1 个回答 | 0
1
个回答提问
get_param fails with simscape block
Weird/unexpected behavior, not sure if it's a bug. I'm trying to use get_param to access a stock simscape thermal component. I...
2 years 前 | 1 个回答 | 0
1
个回答已回答
Basic Slider Switch question
I think I figured out a way. I hope there's a better solution because this seems like a royal pain. 1) in the simscape compone...
Basic Slider Switch question
I think I figured out a way. I hope there's a better solution because this seems like a royal pain. 1) in the simscape compone...
2 years 前 | 0
已回答
Basic Slider Switch question
I think I'm getting closer to an answer here. I setup slider switch to control a constant block, which feeds a data store wri...
Basic Slider Switch question
I think I'm getting closer to an answer here. I setup slider switch to control a constant block, which feeds a data store wri...
2 years 前 | 0
提问
Simscape Block Parameter not Tunable
I wish to control a Simscape block parameter using the dashboard slider switch. I select Temperature Source, but the slider swi...
2 years 前 | 1 个回答 | 0
1
个回答提问
Simulink dashboard switch to control masked parameter
I wanted to have a slider switch control such that On position would make it 1 Ohm and off position would make it 5 ohms. The s...
2 years 前 | 1 个回答 | 0
1
个回答已回答
Two circles geometry problems
Not clear from the second drawing what the dl of interest is. Let's assume dl is the distance between the left edge of each ci...
Two circles geometry problems
Not clear from the second drawing what the dl of interest is. Let's assume dl is the distance between the left edge of each ci...
2 years 前 | 0
| 已接受
已回答
Control Design Onramp with Simulink
Enter learning.simulink.launchOnramp('controls') in your MATLAB window.
Control Design Onramp with Simulink
Enter learning.simulink.launchOnramp('controls') in your MATLAB window.
2 years 前 | 2
提问
Parameter Writer block not recognizing blocks
In image below I show a sim with a slider switch that modifies the constant block on the left. This the uses a goto/from block ...
2 years 前 | 1 个回答 | 0
1
个回答已回答
Is there a way to nest transfer functions?
Okay, nevermind, found the solution is to use s = tf('s') rather than tf([num dem]).
Is there a way to nest transfer functions?
Okay, nevermind, found the solution is to use s = tf('s') rather than tf([num dem]).
2 years 前 | 0
| 已接受
提问
Is there a way to nest transfer functions?
I wish to build up a transfer function inside a for loop such that each iteration builds up a new transfer function based on pre...
2 years 前 | 1 个回答 | 0
1
个回答提问
Basic Slider Switch question
I was curious if it was possible to make a slider switch dashboard element control more than one block simultaneously. Alterna...
2 years 前 | 3 个回答 | 0
3
个回答已回答
Simscape/Simulink persistent variable in algebraic loop
I think I managed to figure out a solution. As suggested elsewhere a delay block can "break" the algebraic loop. I needed thr...
Simscape/Simulink persistent variable in algebraic loop
I think I managed to figure out a solution. As suggested elsewhere a delay block can "break" the algebraic loop. I needed thr...
2 years 前 | 0
| 已接受
提问
Simscape/Simulink persistent variable in algebraic loop
I have a simple Simscape electrical model containg a circuit that trips if a current is exceeded. I want the trip to happen a c...
2 years 前 | 2 个回答 | 0
2
个回答提问
Generate Zth transient thermal impedance curves with Simscape
Simscape has some nice thermal domain elements like Cauer thermal model elements. I was looking to generate a set of Zth curves...
2 years 前 | 1 个回答 | 0
1
个回答提问
Trying to convert Kelvin to Celsius in Simscape code
I have a simulation with some Simscape Thermal and Electrical elements. The electrical element is a modification of the stock t...
3 years 前 | 1 个回答 | 0
1
个回答提问
simscape block node arrangement
In the IGBT example here: https://www.mathworks.com/help/physmod/sps/ug/Troubleshoot-of-spice-nigbt-conversion.html the gener...
3 years 前 | 1 个回答 | 0