Embedded Coder Support Package for STMicroelectronics STM32 Processors 快速入门
学习 Embedded Coder® Support Package for STMicroelectronics® STM32 Processors 基础知识
教程
- 基于 STMicroelectronics STM32 处理器的板快速入门
此示例说明如何使用 Embedded Coder® Support Package for STMicroelectronics® STM32 Processors 在基于 STMicroelectronics STM32 处理器的硬件板上运行 Simulink® 模型。
- 使用基于 STM32 处理器的板对三相 AC 电机进行开环控制
此示例使用开环控制（也称为标量控制或伏特/赫兹控制）来运行电机。这种方法会改变定子电压和频率来控制转子转速，而不使用来自电机的任何反馈。您可以使用这种方法来检查硬件连接的完整性。开环控制的恒速应用使用固定频率的电机电源。开环控制的可调速应用需要可变频率电源来控制转子转速。为了确保恒定的定子磁通，请保持电源电压振幅与其频率成比例。
- 使用 Analog to Digital Converter 模块支持基于 STMicroelectronics STM32 处理器的板
此示例说明如何在 Simulink® 模型中使用 Analog to Digital Converter 模块，通过 Embedded Coder® Support Package for STMicroelectronics® STM32 Processors 对连接到模拟输入通道的模拟信号进行数字化处理。
- Communication Using CAN or FDCAN Blocks for STMicroelectronics STM32 Processor Based Boards
This example shows how to use CAN or FDCAN blocks to communicate with the STM32 processor based boards using Embedded Coder® Support Package for STMicroelectronics® STM32 Processors Based Boards.
- Signal Monitoring and Parameter Tuning of Generated PWM Output
This example shows how to use PWM Output block in a Simulink® model to generate PWM signals using Embedded Coder® Support Package for STMicroelectronics® STM32 Processors.
- Code Verification and Validation with PIL for STMicroelectronics STM32 Processors Based Boards
This example shows how to use Embedded Coder® Support Package for STMicroelectronics® STM32 Processors for code verification and validation using Processor-in-the-Loop (PIL).
STM32 建模基础知识
- 为基于 STM32 处理器的板设置调度选项
为基于 STM32 处理器的板设置调度选项。
- 使用 STM32CubeMX 和 Simulink 配置基于 STM32 处理器的板
配置基于 STM32 处理器的板以在 Simulink 中使用 STM32CubeMX 工程。
- Serial Configuration for Monitor & Tune and PIL for STM32 Processor-Based Boards
Configure your model to run in Monitor & Tune (External mode) and PIL for STM32 Processor-Based Boards.
- 为基于 STM32 处理器的板配置 STM32CubeMX 中的以太网选项
STM32CubeMX 工程中的以太网配置。
- 在 STM32CubeIDE 中调试 Simulink 生成代码
将 Simulink® 生成代码与 STM32CubeIDE 集成。
精选示例
Generate Motor Control Models for Selected Algorithm and Hardware
Use Motor Control Blockset™ to generate a Simulink® model that is configured for a specific hardware and motor control technique.
使用基于 STM32 处理器的板实现 PMSM 的无传感器磁场定向控制
此示例采用磁场定向控制 (FOC) 方法来控制三相永磁同步电机 (PMSM) 的转速。有关 FOC 的详细信息，请参阅磁场定向控制 (FOC) (Motor Control Blockset)。
Field-Oriented Control of PMSM with Hall Sensor Using STM32G4xx Based Processors
Implements the field-oriented control (FOC) technique to control the speed of a three-phase permanent magnet synchronous motor (PMSM). The FOC algorithm requires rotor position feedback, which is obtained by a Hall sensor.
Voltage Mode Control of DC-DC Buck Converter and Boost Converter Using STMicroelectronics STM32 Processor
Implement a DC-DC buck converter or Boost Converter control system using the B-G474E-DPOW1 Discovery kit for Embedded Coder® Support Package for STMicroelectronics® STM32 Processors.
使用基于 STMicroelectronics STM32 处理器的板进行监控和调节
此示例说明如何使用 Embedded Coder® Support Package for STMicroelectronics® STM32 Processors 在基于 STM32 处理器的板上监控和调节仿真。
Getting Started with Hardware Profiling
Demonstrates how to perform real-time execution profiling of algorithms using the Embedded Coder® Support Package for STMicroelectronics® STM32 Processors. It covers two primary profiling methods:
Getting Started with STM32H7xx-Based Dual-Core Boards
Use the Embedded Coder® Support Package for STMicroelectronics® STM32 Processors to run a Simulink® model on a STM32 H7xx-based dual-core board.
Field-Oriented Control of PMSM Using Position Estimated by Neural Network on STM32 Processor Based Boards
Implement field-oriented control (FOC) of a permanent magnet synchronous motor (PMSM) using rotor position estimated by an auto-regressive neural network (ARNN) trained with Deep Learning Toolbox™.
