graphs dnt show anymore, eventhough the values are shown in the workspace.

Question

sadat golz 2024-3-21

0
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/2097321-graphs-dnt-show-anymore-eventhough-the-values-are-shown-in-the-workspace

编辑： Voss 2024-3-23

Graphs.jpg

Hi,

As you can see from the image I attached. I get my values in the workspace, but suddenly the graphs do not show anymore. Before that the graphs were shown. I did not change anything. Does anyone know whats wrong? URGENT

2 个评论
显示无隐藏无

Dyuman Joshi 2024-3-21

As it is "URGENT", we can not run a badly taken screenshot.

Copy and paste your code here and provide all necessary files needed to run it.

sadat golz 2024-3-21

在 MATLAB Online 中打开

AUM4_MV_portfolio_sim.slx

clc        % clears all inputs and outputs from the command window
clear all  % clears all data in the workspace of matlab
close all  % close all figures produced by matlab
%% Define vehicle paramteters 
v = 30/3.6;       % vehicle speed [m/s]
a = 1.329;        % lenght from front axle to COG [m]
b = 1.561;        % length from rear axle to COG [m]
L = a+b;          % wheelbase [m]
I_yy = 4346.60;   % moment of inertia [kgm^2] 
t_delay= L/v;     % time delay between the front axle and rear axle [s]
%% Define spring parameters
C_f = 58982.63;     % front spring stiffnes [N/m]
C_r = 58982.63;     % rear spring stiffness [N/m]
k_f = 7006.15;      % front damping constant [Ns/m]
k_r = 7006.15;      % rear damping constant [Ns/m]
%% Define vehicle mass distribution
m_tot = 2405;                                    % total vehicle mass [kg]
m_c = m_tot*(1-(I_yy/(m_tot*a*b)));              % coupling mass [kg]
m_f = (I_yy/(a*(a+b)));                          % 46% mass at the front axle [kg]
m_r = (I_yy/(b*(a+b)));                          % 54% mass at the rear axle [kg]
         
%% Define obstacle parameter 
z_i=0.1;                                         % speed bump's height [m]
%% Signal builder and ploting the graphs 
% for creating the vertical displacement, a signal builder is used to represent a speed bumpers height of 0.1 [m]
% we must take the time delay between front axle and the rear axle into
% consideration
disp('script to illustrate the graph')
% defining four set points in the signal builder
% 1st point 
t1 = 0;
y1 = 0;
% 2nd point
t2 = 1/v;
y2 = 0;
% 3rd point
t3 = 2/v;
y3 = 0.1;
% 4th point
t4 = 3/v;
y4 = 0.1;
% 5th point 
t5 = 4/v;
y5 = 0;
% 6th point
t6 = 5/v;
y6 = 0;
% defining the points in array
t = [t1 t2 t3 t4 t5 t6];
y = [y1 y2 y3 y4 y5 y6];
% defining the array in the signal builder where z_1 is the signal input ofthe model
signalbuilder('AUM4_MV_portfolio_sim/speed_bumper','set','speed_bumper','Group 1',t,y)
% simulating the simulink model
sim('AUM4_MV_portfolio_sim')
% graph 1: sprung mass vs road input vs time
subplot(3,1,1)
plot1 = plot(tout,disp_front,'blue',tout,disp_rear,'red',tout,speed_bump,'green');
legend('Sprung mass front','Sprung mass rear', 'Speed bumper')
grid on
xlabel('Time [s]')
ylabel('Displacement [m]')
title 'Front & rear displacement'
% graph 2: pitch vs time
subplot(3,1,2)
plot3 = plot(tout,pitch_angle);
legend('Pitch angle')
grid on
xlabel('Time [s]')
ylabel('Pitch[radians]')
title 'Pitch angle'
% graph 3: suspension forces vs time
subplot (3,1,3)
plot2 = plot(tout,spring_force_front,tout,spring_force_rear);
legend('Suspension force front','Suspension force rear')
grid on
xlabel('Time[s]')
ylabel('Force[N]')
title 'Suspension forces'