How to fix legend error??
显示 更早的评论
Hi
my code is running well but I have a legend error
when I write 'legend('Curve Name')' it appears only the first one
(Warning: Ignoring extra legend entries.
> In legend>set_children_and_strings (line 646)
In legend>make_legend (line 316)
In legend (line 259)
In finalstepsolar (line 68)
Warning: Ignoring extra legend entries.
> In legend>set_children_and_strings (line 646)
In legend>make_legend (line 316)
In legend (line 259)
In finalstepsolar (line 82)
>> )
any help please
K=1.38065e-23; %Boltzman Constant
q=1.602e-19; %Electron's Charge
Iscn=3.8; %Desigerable Short Circuit Current
Vocn=21.1; % Desigerable Open Circuit Voltage
Kv=-0.073; % Temperature Voltage Constant
Ki=0.003; %Temperature Current Constant
Ns=36; %Number of Series Conected Cells
Np=6;
T=25+273; % Operating Temperature in Kelvin
Tn=30+273; %Temperature at STC
Gn=1000; %Irradiance at STC
A=3.3; %Diode Ideality Constant
%%A= [Si-mono=1.2, Si- poly =1.3, a-Si:Hi=1.8,a-Si:Hitandem=3.3,a-Si:Hitriple=5, CdTe=1.5, CIS=1.5, AsGa=1.3 ]
a=(Ns*A*K*Tn)/q;
Eg=1.2; %Band Gap of silicon at Temperature of STC condition [ 25 deg. Cel]
G=1000; %Actual Irradiance
Rs=0.221; %Series Resistance of Equivalent PV cell
Rp=415.405; %Parallel Resistance of Equivalent PV cell
%%%%%%%%%%%%%%% Parameter's Value Calculation %%%%%%%%%%%%%%%%%
Tn2=80+273;
for Tni=Tn:5:Tn2
Vtn=Ns*((K*Tn)/q); % Equation 2
I0n=Iscn/((exp(Vocn/(a*Vtn)))-1); % Equation 5
I0=I0n*((Tni/T)^3)*exp(((q*Eg/(a*K))*((1/Tni)-(1/T)))); %Equation 4
Ipvn=Iscn;
Ipv=(G/Gn)*(Ipvn+Ki*(T-Tni)); %Equation 3
Vt=Ns*((K*T)/q);
i=1;
I(1)=0;
for (V=Vocn: -0.1:0)
I_term1=I0*(exp((V+I(i)*Rs)/(Vt*a))-1)*Np; %Part of Equation 1
I_term2= (V+I(i)*Rs)/Rp; % Part of Equation 1
I(i+1)=Ipv-(I_term1+I_term2); %Equation 1
%%%%Ipv(i)=(G/Gn)*(Ipvn+Ki*(T-Tni));
if I(i)>0 % Negative Power and Current Control Loop
I(i)=I(i);
else
I(i)=0;
end
Pi(i)=V*I(i);
Vi(i)=V;
i=i+1;
end
%%%%%%%%%%%% Graphical Interface %%%%%%%%%%%%%%%%%%%
figure
hold on;
plot(Vi(1:i-1),I(1:i-1),'b', 'Linewidth',1.5)
xlabel('Voltage (volt)');
ylabel('Current (Amp)');
legend('T=30 C','T=35 C','T=40 C','T=45 C','T=50 C','T=55 C','T=60 C','T=65 C','T=70 C','T=75 C','T=80 C')
idxmax = find(Pi == max(Pi));
figure
plot(Vi(1:i-1),Pi(1:i-1), '-p','MarkerIndices',[ idxmax],...
'MarkerFaceColor','red',...
'MarkerSize',8)
xlabel('Voltage (volt)');
ylabel('Power (Watt)');
legend('T=30 C','T=35 C','T=40 C','T=45 C','T=50 C','T=55 C','T=60 C','T=65 C','T=70 C','T=75 C','T=80 C')
end
4 个评论
Jonas
2021-4-29
if you plot in a loop and you want all plots to be to be in the same figure then please call figure() once before the loop and the legend() command once after the loop
Avoid confusing useless expressions like: I(i)=I(i); This wastes time only.w
if I(i)>0 % Negative Power and Current Control Loop
I(i)=I(i);
else
I(i)=0;
end
% Nicer:
I(i) = max(0, I(i)); % [EDITED, Thanks Raymond]
Raymond Norris
2021-4-29
max, not min, right?
zina shadidi
2021-4-30
采纳的回答
Try this —
K=1.38065e-23; %Boltzman Constant
q=1.602e-19; %Electron's Charge
Iscn=3.8; %Desigerable Short Circuit Current
Vocn=21.1; % Desigerable Open Circuit Voltage
Kv=-0.073; % Temperature Voltage Constant
Ki=0.003; %Temperature Current Constant
Ns=36; %Number of Series Conected Cells
Np=6;
T=25+273; % Operating Temperature in Kelvin
Tn=30+273; %Temperature at STC
Gn=1000; %Irradiance at STC
A=3.3; %Diode Ideality Constant
%%A= [Si-mono=1.2, Si- poly =1.3, a-Si:Hi=1.8,a-Si:Hitandem=3.3,a-Si:Hitriple=5, CdTe=1.5, CIS=1.5, AsGa=1.3 ]
a=(Ns*A*K*Tn)/q;
Eg=1.2; %Band Gap of silicon at Temperature of STC condition [ 25 deg. Cel]
G=1000; %Actual Irradiance
Rs=0.221; %Series Resistance of Equivalent PV cell
Rp=415.405; %Parallel Resistance of Equivalent PV cell
%%%%%%%%%%%%%%% Parameter's Value Calculation %%%%%%%%%%%%%%%%%
Tn2=80+273;
Dname1 = {'T=30 C','T=35 C','T=40 C','T=45 C','T=50 C','T=55 C','T=60 C','T=65 C','T=70 C','T=75 C','T=80 C'};
figure
hold on
k1 = 0;
for Tni=Tn:5:Tn2
k1 = k1+1;
Vtn=Ns*((K*Tn)/q); % Equation 2
I0n=Iscn/((exp(Vocn/(a*Vtn)))-1); % Equation 5
I0=I0n*((Tni/T)^3)*exp(((q*Eg/(a*K))*((1/Tni)-(1/T)))); %Equation 4
Ipvn=Iscn;
Ipv=(G/Gn)*(Ipvn+Ki*(T-Tni)); %Equation 3
Vt=Ns*((K*T)/q);
i=1;
I(1)=0;
for (V=Vocn: -0.1:0)
I_term1=I0*(exp((V+I(i)*Rs)/(Vt*a))-1)*Np; %Part of Equation 1
I_term2= (V+I(i)*Rs)/Rp; % Part of Equation 1
I(i+1)=Ipv-(I_term1+I_term2); %Equation 1
%%%%Ipv(i)=(G/Gn)*(Ipvn+Ki*(T-Tni));
if I(i)>0 % Negative Power and Current Control Loop
I(i)=I(i);
else
I(i)=0;
end
Pi(i)=V*I(i);
Vi(i)=V;
i=i+1;
end
%%%%%%%%%%%% Graphical Interface %%%%%%%%%%%%%%%%%%%
% figure
subplot(2,2,1)
hold on
plot(Vi(1:i-1),I(1:i-1),'b', 'Linewidth',1.5, 'DisplayName',Dname1{k1})
xlabel('Voltage (volt)');
ylabel('Current (Amp)');
% legend('T=30 C','T=35 C','T=40 C','T=45 C','T=50 C','T=55 C','T=60 C','T=65 C','T=70 C','T=75 C','T=80 C')
idxmax = find(Pi == max(Pi));
% figure
subplot(2,2,2)
hold on
plot(Vi(1:i-1),Pi(1:i-1), '-p','MarkerIndices',[ idxmax],...
'MarkerFaceColor','red',...
'MarkerSize',8, 'DisplayName',Dname1{k1})
xlabel('Voltage (volt)');
ylabel('Power (Watt)');
hl = legend;
end
hold off
subplot(2,2,[3 4])
Ax = gca;
Ax.Visible = 'off';
pos = Ax.Position
hl.NumColumns = 3;
hl.Position = pos;
I added the ‘k1’ counter and changed the order of the figure and hold calls, and changed the legend call to include 'DisplayName' strings.
This should get you closer to the result you want.
更多回答（0 个）
类别
在 帮助中心 和 File Exchange 中查找有关 Annotations 的更多信息
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!
Translated by 
