![photo](/responsive_image/150/150/0/0/0/cache/matlabcentral/profiles/2339396.jpg)
Magdi Nabi
自 2012 起处于活动状态
Followers: 0 Following: 0
Professional Interests: Process control, Neural network,PID controller, simulink
Feeds
已回答
Is it possible to design a controller in simulink using experimental data only?
Hi, i need to design model like yours but the input is flow ( 2 inputs) and 1 out put i need to control the flow by vary the sp...
Is it possible to design a controller in simulink using experimental data only?
Hi, i need to design model like yours but the input is flow ( 2 inputs) and 1 out put i need to control the flow by vary the sp...
7 years 前 | 0
已回答
Is possible uses PLC Code Generation with MPC (Model Predictive Control)
hi, just an inquiry, are you saying i can implement MPC to Rockwell PLC unit (Allen Bradley)? the reason i am asking i am de...
Is possible uses PLC Code Generation with MPC (Model Predictive Control)
hi, just an inquiry, are you saying i can implement MPC to Rockwell PLC unit (Allen Bradley)? the reason i am asking i am de...
7 years 前 | 0
提问
Design closed loop system and convert to PLC
Hi All, i am trying to design feed-forward feedback controller for a machine ( i don't have mathematical model for this machine...
7 years 前 | 0 个回答 | 0
0
个回答提问
How do we model and design a controller for a machine has no mathematical model? whats the best way ?
my task is to control a machine (process control) has no first principle model(mathematical model), but we manage to collect rea...
7 years 前 | 1 个回答 | 0
1
个回答提问
what sensor i can use to measure thick liquid density (thickness)?
Hi all, i appreciate your help and i am looking to measure sludge thickener inline (pipe), thinking to use micro-bending fibe...
8 years 前 | 0 个回答 | 0
0
个回答提问
matlab code for equations below (model predictive control)
x(k)=Ax(k-1)+BU(k-1) A= 78 B=[35 20 10] U=[22;13;2] x(k+1)=A^(2)*x(k-1)+A*B*U(k-1)+B*U(k) x(k+2)=A^(3)*x(k-1)+A^(2)*B*U(k...
11 years 前 | 1 个回答 | 0
1
个回答提问
integrator behavioure, how it works
hi, what if i replace the initial condition of the integrator with the set point, the refernce signal that i am trying to rea...
11 years 前 | 0 个回答 | 0
0
个回答提问
sim command problem, the model not run for desired time
hi all, i have problem using sim command, [Tout,X,Y1,Y2]=sim('mymodel',[realT,[],[realT[u;u]]) Ts=4sec N=2000sec rea...
11 years 前 | 0 个回答 | 0
0
个回答提问
simulink model run for short time when i use sim command
hi, i have problem when i use sim command to call my simulink model, the model just run for short time that it should be, i m...
11 years 前 | 0 个回答 | 0
0
个回答提问
MPC volterra Model
Hi guys, actually i would like to design an MPC Volterra model to control my system, actually i dont know from where i can st...
12 years 前 | 0 个回答 | 0
0
个回答提问
PID self Tuner
hi guys, i have got an error message when i connecte the model to the PID tuner trying to linearize the model but i got a mes...
12 years 前 | 1 个回答 | 0
1
个回答提问
mex-setup/ matlab
hi i did run mex-setup after install C++ express and SDK and i got this error ( Could not find the compiler "cl" on the DOS pat...
12 years 前 | 1 个回答 | 0
1
个回答提问
MPC Block
hi Guys i am using Matlab 2010b on university computer, and i can not find the MPC block in simulink so is there any way to d...
12 years 前 | 1 个回答 | 0
1
个回答已回答
Matlab Simulink
thanx for your help, and actually i found that my computer does not has C++ and SDK and i did down load them and the previous er...
Matlab Simulink
thanx for your help, and actually i found that my computer does not has C++ and SDK and i did down load them and the previous er...
12 years 前 | 0
提问
Matlab Simulink
Hi guys, i have problem with simulink as when i run my simulink model the message comes up on matlab: (Unable to locate a C-c...
12 years 前 | 2 个回答 | 0