Feeds
已回答
Fixing display of GUIDE GUI on R2025a
Hi, Could you check if the information on legacy UI frameworks in the below link is relevant to your issue? https://www.math...
Fixing display of GUIDE GUI on R2025a
Hi, Could you check if the information on legacy UI frameworks in the below link is relevant to your issue? https://www.math...
7 days 前 | 1
已回答
Error occurred while build the demo model tc4x_8ledsBlinky for TC4Dx
Hi Andy, The demo uses peripheral blocks from the ‘AURIX TC4x’ library. In Simulink R2024b, these blocks are only supported fo...
Error occurred while build the demo model tc4x_8ledsBlinky for TC4Dx
Hi Andy, The demo uses peripheral blocks from the ‘AURIX TC4x’ library. In Simulink R2024b, these blocks are only supported fo...
11 days 前 | 0
已回答
Colorbar distortion when figure saved as PDF
Hi, I understand that the colorbar lines are being distorted when you are saving the MATLAB figure as a pdf file in R2025a on ...
Colorbar distortion when figure saved as PDF
Hi, I understand that the colorbar lines are being distorted when you are saving the MATLAB figure as a pdf file in R2025a on ...
11 days 前 | 0
已回答
Quaternions Inconsistency and Mask Access Limitation in Aerospace Blockset (Simulink 2024b vs. 2025a)
Hi Oscar, In Simulink R2024b, I notice that in the ‘6DoF (Quaternion)’ block in Aerospace blockset, the quaternion representati...
Quaternions Inconsistency and Mask Access Limitation in Aerospace Blockset (Simulink 2024b vs. 2025a)
Hi Oscar, In Simulink R2024b, I notice that in the ‘6DoF (Quaternion)’ block in Aerospace blockset, the quaternion representati...
14 days 前 | 0
已回答
How can I create SPWM from ePWM blocks for C2000 in Simulink?
Hi Semih, I understand that you are implementing SPWM using ePWM in Simulink and observing a phase misalignment and drift betwe...
How can I create SPWM from ePWM blocks for C2000 in Simulink?
Hi Semih, I understand that you are implementing SPWM using ePWM in Simulink and observing a phase misalignment and drift betwe...
14 days 前 | 0
已回答
How to fix my controll and strategy of Series Hybrid Transmission
Hi Nico, The following changes in the model would resolve the issue. Change 1: In the model, the output from ‘App’ port is an ...
How to fix my controll and strategy of Series Hybrid Transmission
Hi Nico, The following changes in the model would resolve the issue. Change 1: In the model, the output from ‘App’ port is an ...
20 days 前 | 0
已回答
Power output mismatch in simulating electric drivetrain, where expected power flow is Pbatt>Pdcdc>Pdcac>Pmotor,. I dont see that in my simulation.
Hi Bharat, When Simscape components are packaged as subsystem and connected via I/O ports, the physical connections are replac...
Power output mismatch in simulating electric drivetrain, where expected power flow is Pbatt>Pdcdc>Pdcac>Pmotor,. I dont see that in my simulation.
Hi Bharat, When Simscape components are packaged as subsystem and connected via I/O ports, the physical connections are replac...
21 days 前 | 0
已回答
Assistance Required for VTOL SITL Setup and Unreal Engine 5.3 Visualization with MATLAB R2025a
Hi Ankit, TheUAV toolbox interface in MATLAB doessupports PX4 SITL (Software in the Loop) workflow. For integrating a Simulink...
Assistance Required for VTOL SITL Setup and Unreal Engine 5.3 Visualization with MATLAB R2025a
Hi Ankit, TheUAV toolbox interface in MATLAB doessupports PX4 SITL (Software in the Loop) workflow. For integrating a Simulink...
21 days 前 | 0
已回答
Using Estimate Parameter with a question
Hi In the ‘Engine Throttle Model’, the variable ‘time1’ is a time series data containing the time instances at which throttle ...
Using Estimate Parameter with a question
Hi In the ‘Engine Throttle Model’, the variable ‘time1’ is a time series data containing the time instances at which throttle ...
22 days 前 | 0
| 已接受
已回答
Error using datcomimport. Problem with arrays sizes.
Hi Antonio, The "fastuav_drone.out" file has a floating-point data mismatch, which is causing the error when importing data wi...
Error using datcomimport. Problem with arrays sizes.
Hi Antonio, The "fastuav_drone.out" file has a floating-point data mismatch, which is causing the error when importing data wi...
25 days 前 | 2
已回答
How to plot bode (Vout/Vin) of a circuit model in simulink?
Hi Peter, The 'Model Linearizer' in the Simulink linearizes the system about an operating point. By default, the initial condi...
How to plot bode (Vout/Vin) of a circuit model in simulink?
Hi Peter, The 'Model Linearizer' in the Simulink linearizes the system about an operating point. By default, the initial condi...
27 days 前 | 1
已回答
R2025a: Simulink scope does not show full data resolution when zooming in during simulation
Hi Simon, I also encountered the same issue while working with the Simulink in R2025a. I observed the Scope block shows a decim...
R2025a: Simulink scope does not show full data resolution when zooming in during simulation
Hi Simon, I also encountered the same issue while working with the Simulink in R2025a. I observed the Scope block shows a decim...
28 days 前 | 0
