photo

owen chang


Last seen: 5 years 前 自 2013 起处于活动状态

Followers: 0   Following: 0

消息

统计学

MATLAB Answers

9 个提问
0 个回答

排名
37,532
of 299,830

声誉
1

贡献数
9 个提问
0 个回答

回答接受率
22.22%

收到投票数
1

排名
 of 20,813

声誉
N/A

平均
0.00

贡献数
0 文件

下载次数
0

ALL TIME 下载次数
0

排名

of 166,163

贡献数
0 个问题
0 个答案

评分
0

徽章数量
0

贡献数
0 帖子

贡献数
0 公开的 个频道

平均

贡献数
0 个亮点

平均赞数

  • Thankful Level 1

查看徽章

Feeds

排序方式:

提问


why exportONNXNetwork will add additional "Sub" in onnx, how to remove this layer in onnx?
Hi, i did the following: >> baseNetwork = resnet50; >> exportONNXNetwork(baseNetwork,'resnet50-matlab'); but when compare sam...

6 years 前 | 1 个回答 | 0

1

个回答

提问


how to deploy deep learning prototype to FPGA using HDL Coder?
Hi i have FPGA platform and like to play around with Matlab deep learning (like MatConvNet), then deploy on my FPGA platform fo...

8 years 前 | 1 个回答 | 0

1

个回答

提问


running open_system('hdlcoder_led_blinking') for zynq, but no connection?
Hi, i am using usb jtag cable for communication with zynq-zc702, but i can't see serialport as instructed in the webinar, how sh...

12 years 前 | 1 个回答 | 0

1

个回答

提问


how could i generate an axi-stream or axi4-lite dma master by hdl coder?
Hi, i found the current demo using only axi-stream slave interface in sobel image processing system. however, it might require a...

12 years 前 | 1 个回答 | 0

1

个回答

提问


HDL Stream FFT in HDL Coder 2013b, not support AXI4-Stream Interface? (single rate?)
Hi, i have built a system involving Stream FFT with AXI4-Stream Interface, the goal is to put this design into Zynq, so AXI4-St...

12 years 前 | 1 个回答 | 0

1

个回答

提问


Failed Streaming interface is not supported when the DUT is not single rate
Hi, the AXI-Stream interface for Stream FFT is requiring DUT "single rate", but i can't find where to set it, and what does it ...

12 years 前 | 0 个回答 | 0

0

个回答

提问


HDL Stream FFT in HDL Coder 2013b, not support FPGA?
Hi, i am using Stream FFT for Zynq, but once i have created the subsystem and set it to Atomic, i have this error message pop u...

12 years 前 | 1 个回答 | 0

1

个回答

提问


How to create a FFT ipcore for Zynq using Simulink HDL Coder?
there is an error message "not support for frame based module"? is there any other solution for exporting signal processing bl...

12 years 前 | 2 个回答 | 1

2

个回答

提问


Does HDL coder from Simulink support AXI-4 Stream Interface for Xilinx Zynq?
Hi all, I have created an adder example and export to Xilinx Vivado 2013.2 using HDL coder, and integrated using Vivado IPI. th...

12 years 前 | 1 个回答 | 0

1

个回答