Feeds
已回答
Error in building simulink code for PX4-V6x
The reason you faced the compilation issue is that either the expected GCC version (gcc-arm-none-eabi-9-2020-q2) was not install...
Error in building simulink code for PX4-V6x
The reason you faced the compilation issue is that either the expected GCC version (gcc-arm-none-eabi-9-2020-q2) was not install...
1 month 前 | 1
已回答
Is it possible to run px4_simulink_app module in multirate?
Yes, you can schedule different algorithm in Simulink to execute at different rates. The rate at which a module runs is determin...
Is it possible to run px4_simulink_app module in multirate?
Yes, you can schedule different algorithm in Simulink to execute at different rates. The rate at which a module runs is determin...
7 months 前 | 0
| 已接受
已回答
What is the Current State of Connected I/O for PX4
Hi @riley, Connected IO is supported in R2024a and R2024b. Can you give us some more details on the issue here What is the Har...
What is the Current State of Connected I/O for PX4
Hi @riley, Connected IO is supported in R2024a and R2024b. Can you give us some more details on the issue here What is the Har...
7 months 前 | 0
已回答
Custom Matlab System Objects for use with PX4 Architecture (PX4 Serial Receive)
Can you tell us why you needed to modify the source code for Serial block? If it was to read variable length buffer, I just post...
Custom Matlab System Objects for use with PX4 Architecture (PX4 Serial Receive)
Can you tell us why you needed to modify the source code for Serial block? If it was to read variable length buffer, I just post...
8 months 前 | 0
已回答
PX4 Serial Receive Variable Data Length
Yes, The PX4 Serial receive has a checkbox in Advanced tab called "Output partially received data". When this parameter is enabl...
PX4 Serial Receive Variable Data Length
Yes, The PX4 Serial receive has a checkbox in Advanced tab called "Output partially received data". When this parameter is enabl...
8 months 前 | 0
| 已接受
已回答
FixedwingGNC model issue while limiting it to guided taxi mission
Can you underline in your snapshot of the model where you have made the changes? OR you can share more zoomed in snapshots of th...
FixedwingGNC model issue while limiting it to guided taxi mission
Can you underline in your snapshot of the model where you have made the changes? OR you can share more zoomed in snapshots of th...
9 months 前 | 0
已回答
UAV Toolbox Support for PX4 Autopilots - HIL_SENSOR MAVLink message data not accepted by stock PX4 flight controller
Can you clarify whether with the Python file you were able to clear warnings? Is it just with the Simulink model you see the las...
UAV Toolbox Support for PX4 Autopilots - HIL_SENSOR MAVLink message data not accepted by stock PX4 flight controller
Can you clarify whether with the Python file you were able to clear warnings? Is it just with the Simulink model you see the las...
9 months 前 | 0
已回答
Pixhawk 6c : monitor and tune error when using telemtry
Can you try changing the baud rate of /dev/ttyS5 to 57600 in the configuration settings and try External mode again?
Pixhawk 6c : monitor and tune error when using telemtry
Can you try changing the baud rate of /dev/ttyS5 to 57600 in the configuration settings and try External mode again?
9 months 前 | 0
已回答
Firmware Build Failure in hardware setup
It seems like you are using R2023b version of MATLAB. If yes, we highly recommend upgrading to the latest version R2024b and use...
Firmware Build Failure in hardware setup
It seems like you are using R2023b version of MATLAB. If yes, we highly recommend upgrading to the latest version R2024b and use...
9 months 前 | 0
已回答
Libreria UAV Toolbox Pixhawk de Matlab soporta Pixhawk 6c mini?
Although Pixhawk 6c Mini is not officially supported, you can still use the board by selecting Pixhawk 6c as the hardware target...
Libreria UAV Toolbox Pixhawk de Matlab soporta Pixhawk 6c mini?
Although Pixhawk 6c Mini is not officially supported, you can still use the board by selecting Pixhawk 6c as the hardware target...
9 months 前 | 0
已回答
Deploying Custom Controllers on Pixhawk 6X with PX4 Firmware 1.12.3: Compatibility Challenges
There is a newer version of Pixhawk 6x board that requires 1.14.3 PX4 Firmware version. What you can go is Upgrade to MATLAB R2...
Deploying Custom Controllers on Pixhawk 6X with PX4 Firmware 1.12.3: Compatibility Challenges
There is a newer version of Pixhawk 6x board that requires 1.14.3 PX4 Firmware version. What you can go is Upgrade to MATLAB R2...
9 months 前 | 0
已回答
How do I connect and read data from pixhawk 6x when using simulink/ UAVToolbox?
I believe you are running into a known issue where a newer version of the Pixhawk 6x board is only supported by the PX4 Firmware...
How do I connect and read data from pixhawk 6x when using simulink/ UAVToolbox?
I believe you are running into a known issue where a newer version of the Pixhawk 6x board is only supported by the PX4 Firmware...
9 months 前 | 1
已回答
Unable to link PX4 Simulink file to real board OR SITL with JMAVSIM
Can you upgrade to MATLAB R2024a and see if you are still running into this issue?
Unable to link PX4 Simulink file to real board OR SITL with JMAVSIM
Can you upgrade to MATLAB R2024a and see if you are still running into this issue?
1 year 前 | 0
已回答
Accelerometer measuremet of pixhawk 6X using UWAV Toolbox Support Package for PX4 Autopilots, MATLAB 2024a
When the hardware setup process using the hardware setup screens is almost finished, there is a screen at the end called "Test C...
Accelerometer measuremet of pixhawk 6X using UWAV Toolbox Support Package for PX4 Autopilots, MATLAB 2024a
When the hardware setup process using the hardware setup screens is almost finished, there is a screen at the end called "Test C...
1 year 前 | 0
已回答
Why the drone is drifting in HIL?
Try disconnecting and reconnecting PX4 Autopilot hardware connected to your PC and then simulate the plat model again. Restart Q...
Why the drone is drifting in HIL?
Try disconnecting and reconnecting PX4 Autopilot hardware connected to your PC and then simulate the plat model again. Restart Q...
1 year 前 | 0
| 已接受
已回答
Example model overflows board's flash memory, which is the same reported to be used in the example
Can you try using the cubepilot_cubeorange_multicopter build configuration in hardware setup screens instead of the default one?...
Example model overflows board's flash memory, which is the same reported to be used in the example
Can you try using the cubepilot_cubeorange_multicopter build configuration in hardware setup screens instead of the default one?...
1 year 前 | 1
已回答
PX4 HITL simulation timing synch (lockstep) issue
PX4 HITL simulations are not lockstep. Since lockstep simulations are not real time, making HITL simulations lockstep would defe...
PX4 HITL simulation timing synch (lockstep) issue
PX4 HITL simulations are not lockstep. Since lockstep simulations are not real time, making HITL simulations lockstep would defe...
1 year 前 | 1
| 已接受
已回答
Unable to access Model Configuration Parameters for PX4 Flight Controller
Please install the UAV Toolbox Support Package for PX4 Autopilots from the add-on manager
Unable to access Model Configuration Parameters for PX4 Flight Controller
Please install the UAV Toolbox Support Package for PX4 Autopilots from the add-on manager
1 year 前 | 0
已回答
I am implementing the px4demo_attitudeSystem demo on a hexacopter, but I am encountering the following error
The Simulink model 'px4demo_attitudeSystem' contains a model reference 'px4demo_attitude_control'. Open that model (by doing rig...
I am implementing the px4demo_attitudeSystem demo on a hexacopter, but I am encountering the following error
The Simulink model 'px4demo_attitudeSystem' contains a model reference 'px4demo_attitude_control'. Open that model (by doing rig...
1 year 前 | 0
已回答
UAV toolbox support package for PX4 - Design Path Follower Algorithm Example
There is no example available for "Path follower algorithm" workflow in the UAV Toolbox Support Package for PX4 Autopilots
UAV toolbox support package for PX4 - Design Path Follower Algorithm Example
There is no example available for "Path follower algorithm" workflow in the UAV Toolbox Support Package for PX4 Autopilots
1 year 前 | 0
已回答
Compatibility of Pixhawk 2.4.8 with UAV toolbox for PX4
As of R2024a, the UAV Toolbox support package for PX4 autopilots supports PX4 version 1.14. With this firmware version, it is re...
Compatibility of Pixhawk 2.4.8 with UAV toolbox for PX4
As of R2024a, the UAV Toolbox support package for PX4 autopilots supports PX4 version 1.14. With this firmware version, it is re...
1 year 前 | 0
已回答
UAV Toolbox px4 demo host target with Simulink Plant - SITL simulation result question
In the MIL simulation, only the controller is involved. However, when the SITL simulation is run, all of the PX4 modules apart f...
UAV Toolbox px4 demo host target with Simulink Plant - SITL simulation result question
In the MIL simulation, only the controller is involved. However, when the SITL simulation is run, all of the PX4 modules apart f...
2 years 前 | 1
已回答
Obtain msg from Pixhawk
In you MATLAB script, add the below two lines of code dialect = mavlinkdialect("common.xml"); msg = deserializemsg(dialect,buf...
Obtain msg from Pixhawk
In you MATLAB script, add the below two lines of code dialect = mavlinkdialect("common.xml"); msg = deserializemsg(dialect,buf...
2 years 前 | 1
| 已接受
已回答
The PX4 firmware build fails consistently for SITL
Can you try reinstalling the Cygwin toolchain?
The PX4 firmware build fails consistently for SITL
Can you try reinstalling the Cygwin toolchain?
2 years 前 | 0
已回答
not able to verify the installation in setup cygwin toolchain and download px4 source code in UAV toolbox support package for px4 autopilot
We need some more details on the issue. Reach out to MathWorks Tech support
not able to verify the installation in setup cygwin toolchain and download px4 source code in UAV toolbox support package for px4 autopilot
We need some more details on the issue. Reach out to MathWorks Tech support
2 years 前 | 0
| 已接受
已回答
How to use the block "To file" or "To workspace" in PX4 SITL with jmavsim
The use of "To File" or "To workspace" block in SITL mode is not supported. For logging, you need to use Monitor & Tune
How to use the block "To file" or "To workspace" in PX4 SITL with jmavsim
The use of "To File" or "To workspace" block in SITL mode is not supported. For logging, you need to use Monitor & Tune
2 years 前 | 0
| 已接受
已回答
PX4 UAV Toolbox px4demo_attitudeSystem Attitude Controller for a Hexacopter
What does the status output of the RC block indicate?
PX4 UAV Toolbox px4demo_attitudeSystem Attitude Controller for a Hexacopter
What does the status output of the RC block indicate?
2 years 前 | 0
已回答
Error when run example "Px4DemoHostTargetWithSimulinkPlantStart"
Are you trying to generate code for the plant model? The plant model is supposed to run on the host (by clicking run in Simulink...
Error when run example "Px4DemoHostTargetWithSimulinkPlantStart"
Are you trying to generate code for the plant model? The plant model is supposed to run on the host (by clicking run in Simulink...
2 years 前 | 0
已回答
Error in PX4 Firmware Build
Can you try to build the CMake for px4_fmu-v3_default?
Error in PX4 Firmware Build
Can you try to build the CMake for px4_fmu-v3_default?
2 years 前 | 0
已回答
PX4 HIL with Simulink plant: which COM port to select?
You should select COM3.
PX4 HIL with Simulink plant: which COM port to select?
You should select COM3.
2 years 前 | 0
| 已接受
