HDL Verifier and FPGA in the loop
显示 更早的评论
Hello All,
I am trying to use FPGA in the Loop (FIL) using HDL verifier and simulink, but I keep getting the error:
Did not receive version information from the hardware. You must have a valid connection, a compatible development board, and compatible versions of the block and FPGA programming file.
My board atlys board and I am not able to get reply from the board when I ping it. Can anyone tell me where I am wrong?
1 个评论
Walter Roberson
2012-6-2
I received your email, but this is not a topic I have experience with.
The MAC address would be 12 hexadecimal digits.
There are different meanings of "ping" in use. The most common meaning requires knowing the IP address of the destination, but does not require knowing the MAC address. An IP address such as 192.168.0.1 would be common.
回答（8 个）
Tao Jia
2012-8-8
0 个投票
There is a trouble shooting section in the HDL Verifier documentation. Try to see if that one helps you. It's possible a network setting issue.
Pablo Medina
2016-9-15
0 个投票
hi, I am getting the same error. Did you solve your problem? Could you give me a hint?
Thanks, for the future answer.
Prashant Funde
2017-8-3
0 个投票
If this problem is solved please give me some hint.
LIANG GUO
2019-5-10
0 个投票
id not receive version information from the hardware. You must have a valid connection, a compatible development board, and compatible versions of the block and FPGA programming file.
Component: Simulink | Category: Model error
Ricardo Mejia Mertel
2019-10-15
0 个投票
Hello, I know the thread is quite old but anyone was able to solve the problem?
best regards,
Ricardo
It helped in my case to readjust Windows network adapter "TCP/IPv4" properties to match the network settings of the evaluation board. Make sure that the subnet number is the same, but the host number is different. For example: PC IP 192.168.0.1, board's IP 192.168.0.2. Try pinging the board in Windows cmd (ping 192.168.0.2) - it must work.
The strange thing is that all connection checks passed in MATLAB (HDL Workflow advisor, vefircation during board's support package installation) with incorrect network settings, only the model simulation didn't run, until I set the correct network IP.
Mohamed BAGHDADI
2021-1-23
0 个投票
Did not receive version information from the hardware. You must have a valid connection, a compatible development board, and compatible versions of the block and FPGA programming file.
Anyone was able to solve the problem?
PS: I am using Matlab 2019b, altera cyclone IV GX, Quartus prime 18.1 and JTAG Connection
best regards,
6 个评论
xianpeng Li
2022-3-26
I am using JTAG Connection too,.my board is zynq, I can program to the board, but simulate failed. Do you solve it? my message is :
Programming FPGA ...Passed
Running FIL simulation ...Failed
Error:Did not receive version information from the hardware. You must have a valid connection, a compatible development board, and compatible versions of the block and FPGA programming file.
Michelle Thompson
2022-4-14
Same error in both the symmetric filter HDL Coder example and the FIL PID verification example.
"Did not receive version information from the hardware. You must have a valid connection, a compatible development board, and compatible versions of the block and programming file"
Bitstream successfully programmed to the FPGA, but the motor controller simulation and the HDL Coder workflow advisor give the same error.
VIvado hardware manager programs the part with no problems. The zcu106 is connected via JTAG to a computer. The hardware is assigned to a VM. I'm logged into that VM to do this work. MATLAB is running on the same account on the same VM.
MATLAB R2021a, Vivado 2020.2, using the examples from the Mathworks website.
Michelle Thompson
2022-4-14
Same error with the built-in test in the board selection tool.
To stop the test, press "Ctrl+C" in the MATLAB console window.
Starting FPGA-in-the-Loop test ...
Generating FPGA programming file ...Passed
Programming FPGA ...Passed
Running FIL simulation ...Failed
Error:Did not receive version information from the hardware. You must have a valid connection, a compatible development board, and compatible versions of the block and FPGA programming file.
dechen Ai
2022-7-15
The same with you. Have you resoled the problem?
I am using Matlab 2019b, Xilinx zynq xc7z010clg400-1 FPGA baord, Vivado2017.4 and JTAG Connection.
壹 王
2023-6-2
Hello！I receive the same error information.
I used HS2 JTAG cable, xilinx zynq XC7z020400-2, matlab 2021a. Did any fixed this problem ？
Pradeepa Pachalla
2025-7-15
Have you clicked the 'load' button to load the bit file in the FIL subsystem of the generated FIL model? not loading the bit file also generates the error that you are observing.
Anas EL-FECHTALI
2023-5-22
0 个投票
i'm using matlab 2022b to coimplemente on xilinx zynq XC7z020 , but i get an error :
Did not receive version information from the hardware. You must have a valid connection, a compatible development board, and compatible versions of the block and FPGA programming file.
Component:Simulink | Category:Model error
Is here someone who had the same issue?
4 个评论
Anas EL-FECHTALI
2023-5-22
i used JTAG connection
壹 王
2023-6-1
Hello！I receive the same error information.
I used HS2 JTAG cable, xilinx zynq XC7z020400-2, matlab 2021a,Can I have you email for talk ?
Anas EL-FECHTALI
2023-6-13
编辑：Anas EL-FECHTALI
2023-6-13
hello, i solved this issue by respecting matlab vivado compatibility.for matlab 2020Rb you have to get vivado simulator 2020.2, for others:
- R2023a: Xilinx Vivado 2022.1
- R2022b: Xilinx Vivado 2020.2
- R2022a: Xilinx Vivado 2020.2
- R2021b: Xilinx Vivado 2020.1
- R2021a: Xilinx Vivado 2019.2
- R2020b: Xilinx Vivado 2019.2
- R2020a: Xilinx Vivado 2019.1
- R2019b: Xilinx Vivado 2018.3
- R2019a: Xilinx Vivado 2018.2
- R2018b: Xilinx Vivado 2017.4
- R2018a: Xilinx Vivado 2017.2
- R2017b: Xilinx Vivado 2016.4
- R2017a: Xilinx Vivado 2016.2
- R2016b: Xilinx Vivado 2015.4
- R2016a: Xilinx Vivado 2015.2
- R2015b: Xilinx Vivado 2014.4
- R2015a: Xilinx Vivado 2014.2
- R2014b: Xilinx Vivado 2013.4
sencondly, you have to install Hdl verifier support packages , go to Add-ons ---->Get Add-ons in matlab and configurate it. then launch run in your simulink design.
Anas EL-FECHTALI
2023-6-20
sure, my e-mail :elfechtali.forwork.anass@gmail.com
类别
在 帮助中心 和 File Exchange 中查找有关 AMD FPGA and SoC Devices 的更多信息
产品
2025-7-15
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!
Translated by 
