photo

Noam Levine

Last seen: 1 day 前 |  自 2013 起处于活动状态

Followers: 0   Following: 0

统计学

  • Knowledgeable Level 2
  • Revival Level 1
  • First Answer

查看徽章

Feeds

排序方式:

已回答
HW/SW Co-Design with AXI4-Stream Using analog device ADRV9002
Arash - Currently, the ADRV9002 is not supported natively from MATLAB and Simulink. In order to get support, you would need to l...

2 years 前 | 0

| 已接受

已回答
I would like to know if I can try the Aerospace Blockset in my 30 days trial
You can download a trial of Aerospace Blockset at https://www.mathworks.com/products/aerospace-blockset.html. Note that Aerospa...

5 years 前 | 1

已回答
Get data from AD (parallel), is possible?
With the Zedboard (and likely other Zynq-based systems), the converter may be connected to pins tied to programmable logic (PL),...

5 years 前 | 0

已回答
Get data from AD (parallel), is possible?
Jonis - To start, the Communications Toolbox™ Support Package for Xilinx® Zynq®-Based Radio supports the ZedBoard+AD-FMComms2/3/...

5 years 前 | 0

| 已接受

已回答
Cannot find an ADALM-PLUTO radio.
I'm assuming you have Commnications Toolbox installed... If so, here are a couple of things to try: Make sure that no other so...

6 years 前 | 0

已回答
Why do I get a 'Failed to connect to the target' error when I try to run a model in External mode on a Xilinx board?
The Embedded Coder Support Package for Xilinx Zynq Platform will not work with the Zybo board out of the box. You need to create...

6 years 前 | 0

已回答
Zynq embedded coder with zybo is not connecting in external mode
Did you follow our example for creating a custom Zynq reference design to communicate with the Zybo board, or are you trying to ...

6 years 前 | 0

已回答
Using Xilinx SDK 2017.4 with Embedded Coder Support Package for Xilinx Zynq Platform.
Unfortunately, Xilinx SDK version 2017.4 has not been tested with MATLAB R2017b, as it was released after the release of R2017b....

6 years 前 | 0

已回答
Programming target device failed.
Do you also have an Ethernet connection between your ZedBoard and host computer? Before you start the HDL Workflow Advisor, m...

6 years 前 | 0

已回答
MiniZed Support Package for Simulink and Matlab 2018a - how to setup SDK?
Arne - Did you see the new MiniZed support package from Avnet in the Add-On Explorer? They define a MATLAB set-up process, inclu...

6 years 前 | 0

已回答
ADALM-PLUTO Radio Hardware Software Co-Design
The Zynq chip in the ADALM-Pluto is a Z-7010, which has only 28K logic cells, 2.1Mb of block RAM, and 80 DSP slices. The E310 us...

6 years 前 | 1

已回答
System Generator for DSP 14.7 is only compatible with MATLAB 2013b?
Carol - Yes, MATLAB R2013b was likely the last release tested with ISE 14.7, as that was the current MATLAB release available at...

7 years 前 | 0

已回答
configuration between picozed and host Computer
You should be able to log onto the board via a terminal emulation program and set the IP address with the ifconfig command. See ...

7 years 前 | 0

已回答
Simulink- Zynq-7000 several AXI interfaces in the Simulink peripheral
In order for the new reference design (with the additional AXI interface) to be recognized in the hardware/software workflow, wh...

9 years 前 | 0

| 已接受

已回答
running open_system('hdlcoder_led_blinking') for zynq, but no connection?
To run the hdlcoder_led_blinking demo you need three connections: Ethernet cable, UART, and programming cable. Embeded Coder ...

11 years 前 | 0