Community Profile

photo

Manikandan


anna university

Last seen: 5 days 前 自 2012 起处于活动状态

Professional Interests: Electric Drives

统计数据

All
  • Explorer
  • Personal Best Downloads Level 1
  • First Review
  • 5-Star Galaxy Level 2
  • First Submission
  • Revival Level 3
  • First Answer

查看徽章

Content Feed

排序方式:

已回答
PI control techniques for speed control of a BLDC motor
Try to use trial and error method

6 years 前 | 0

已回答
How to change Simulink model line widths
Don't take screen shoot. Go to edit, then copy model to clipboard. after past it as picture in your word. hence the quality of p...

8 years 前 | 3

已提交


Measure the Frequency of given input Square wave
Contact: electricmani@yahoo.co.in

8 years 前 | 7 次下载 |

Thumbnail

已回答
how to control the position of a DC motor by FLC
i completed the same, refer this link, if you want more clarification write me: electricmani@yahoo.co.in http://ieeexplore.ie...

8 years 前 | 0

已回答
Why is the induction motor speed very low and at a negative value
set your scope parameter setting, uncheck limited data points. reduce torque as zero.

8 years 前 | 0

已回答
How to control a brushless motor through a ESC with C2000 using "Embedded Coder" Library in Simulink
I did same like, write me: electricmani@yahoo.co.in

8 years 前 | 0

已回答
Is this the proper way to implement PID for 3 Phase inverter induction motor speed control?
Lot of theoretical methods available to find KP, Ki and Kd values, my suggestion for beginner try to do trial and error method. ...

8 years 前 | 0

已回答
speed control of dc motor using SMC
First start open loop control of motor, verify with closed loop conventional PID controller, then change into SMC.

8 years 前 | 0

已回答
Use PWM to control Speed of brushless dc motor!
use AND gate instead of product block. for more details contact me: electricmani@yahoo.co.in

8 years 前 | 1

已回答
Single phaseInduction motor speed control
Your problem?

8 years 前 | 0

已回答
how to do simulation of speed control of three phase induction motor by v/f method
Contact me: electricmani@yahoo.co.in

8 years 前 | 1

已回答
How to implement speed control of induction motor using Fuzzy logic
Contact me: electricmani@yahoo.co.in

8 years 前 | 0

已回答
How to specify time values and Output values for sawtooth waveform?
Time: [0 2.5000e-005] Output: [0 1]

8 years 前 | 0

已回答
Tuning a pid controller. sampling times must agree?
Motor modeled as mathematical or taken from simpower system tool.

8 years 前 | 0

已回答
Fixed Step Solver Problems
Reduce your sample time as much as possible to small.

8 years 前 | 0

已回答
calculation of time difference between two crossings of voltage waveforms in simulink
Refer my paper: http://www.ripublication.com/ijaer_spl/ijaerv10n10_59.pdf

8 years 前 | 0

已回答
How to determine the controller parameters for BLDC drive?
Refer slandered control system books for ZN method.

8 years 前 | 0

已回答
torque ripple minimisation for bldc motor using direct torue control and indirect flux control
you need to mathematical modeling of motor.

8 years 前 | 1

已回答
Hi, i want to build an bldc motor in motor in matlab , i dont want to use an inbuilt motor block present in simulink .
I tried mathematical modeling of BLDC, but its result differ from simulik library BLDC motor. anybody have clear idea, post here...

8 years 前 | 0

已回答
Servo motor controlling using MATLAB
Yes possible, but you need MATLAB supported hardware. what's your platform wish to work.

8 years 前 | 0

已回答
Ball Screw driven XY table using AC servo motor.
Contact me @ electricmani@yahoo.co.in

8 years 前 | 0

已回答
how to calculate parameters for dc servo motor simulation?
you should contact manufacture or google it to find required data's. not possible to find required data from the available data....

8 years 前 | 0

已回答
Control Servo Motor
use analog output from the real time windows target tool box and select your DAQ via USB. then generate analog output voltage to...

8 years 前 | 0

已回答
Tacho feedback in a servo
If you use simulink for DC motor position control, use motor output speed wm in rad/sec from measurement block. convert equivale...

8 years 前 | 0

已回答
In which location ,we have to store the .fis file?
We need to import the file from work space or call where it was stored, before need to export designed fis to work space. me too...

8 years 前 | 0

已回答
quadrature/rotary encoder .mdl file
I did the same things, if need help contact me on electricmani@yahoo.co.in

8 years 前 | 0

加载更多